Epoxy primer

From Crankshaft Coalition Wiki
Jump to: navigation, search
 
Line 1: Line 1:
{{youcanedit}}
+
 
 
[[Image:54_Dodge_Coronet_in_primer.jpg|right|thumb|350px|A 1954 Dodge Coronet body with a fresh coat of epoxy primer.]]
 
[[Image:54_Dodge_Coronet_in_primer.jpg|right|thumb|350px|A 1954 Dodge Coronet body with a fresh coat of epoxy primer.]]
  
 +
==Overview==
 
Epoxy primer/sealer is a non-porous finish that is typically recommended as the first basecoat over bare steel. Various epoxy primers can also be applied over [[Fiberglassing|fiberglass]], plastic, or the black iron phosphate coating that remains after "converting" [[rust]]. Care must be taken to observe the epoxy maker's recommendations in preparing the surface over which the epoxy is applied.  
 
Epoxy primer/sealer is a non-porous finish that is typically recommended as the first basecoat over bare steel. Various epoxy primers can also be applied over [[Fiberglassing|fiberglass]], plastic, or the black iron phosphate coating that remains after "converting" [[rust]]. Care must be taken to observe the epoxy maker's recommendations in preparing the surface over which the epoxy is applied.  
  
Real epoxy primer is a two-part mix, with a hardener that has to be added before spraying. The common epoxy paint you buy at the local hardware store in an aerosol can is not considered a true epoxy.
+
Real epoxy primer is a two-part mix, with a hardener that has to be added before spraying. The common epoxy paint you buy at the local hardware store in an aerosol can is not considered a true epoxy primer.
 
+
  
 
==Body filler and epoxy primer==
 
==Body filler and epoxy primer==
Line 15: Line 15:
  
 
==Spray (rattle) can epoxy primer==
 
==Spray (rattle) can epoxy primer==
Because epoxy primer must be mixed prior to spraying, it hasn't conventionally been available in a spray can. However, "aerosol 2-component epoxy primer" has recently been introduced by [http://www.rubber-seal.com Rubber-Seal]. To release the activator into the primer, a plunger is inserted into a stem on the bottom of the spray can. Product literature states a pot life of four days.
+
Because epoxy primer must be mixed prior to spraying, it hasn't conventionally been available in a spray can. However, aerosol 2-component epoxy primers have recently been introduced, and are available from [http://www.rustoleumibg.com/product.asp?lvl=P&pnv=2&snv=1&pid=281 Rust-oleum] and [http://www.rubber-seal.com/prodview.asp?prodID=2068 Rubber-Seal]. To release the activator into the primer, a plunger is inserted into a stem on the bottom of the spray can. A review of one such product is available in [http://www.hotrodders.com/forum/solvent-resistant-real-2k-epoxy-aerosol-can-143345.html this discussion].
  
 
==Cautions==
 
==Cautions==
Line 21: Line 21:
  
 
===Temperature===
 
===Temperature===
The temperature of the air and of the metal '''must''' be taken into account -- it must be high enough for the epoxy primer to properly cure. If the temperature drops below proper temp before it is fully cured, the paint will be bad as the chemical reaction does not continue when the temp rises again.
+
The temperature of the air and of the metal '''must''' be taken into account -- it must be high enough for the epoxy primer to properly cure. Note that in cold weather conditions, surface temperatures can be far lower than air temperatures. If the surface temperature drops below a particular value specified by the product manufacturer (usually around 60 degrees F) before it is fully cured, the epoxy may not properly cure even with later applications of heat. A non-contact thermometer can accurately determine if the surface to be sprayed is being maintained at an acceptable temperature.
  
 
===Acids===
 
===Acids===
Some epoxies do not cure properly if put over an acid surface. If you use an acid you must be sure all the acid is neutralized before you paint. The acid will prevent the epoxy from properly curing.
+
Some epoxies do not cure properly if put over an acid surface. If you use an acid you must be sure all the acid is neutralized before you paint. Acid residue may prevent the epoxy from properly curing.
 
+
  
 
==Tech sheets of epoxy primers recommended for automotive use==
 
==Tech sheets of epoxy primers recommended for automotive use==
 +
 +
===Akzo Nobel===
 +
*[http://www.globalsafetynet.com/akzonobel/pdfs/akzo_195_english.pdf SIKKENS Autosurfacer EP (Epoxy Primer) ]
 +
*[http://www.globalsafetynet.com/akzonobel/pdfs/akzo_156_english.pdf LESONAL Epoxy Primer Sealer]
  
 
===DuPont===
 
===DuPont===
Line 50: Line 53:
 
===Southern Polyurethanes===
 
===Southern Polyurethanes===
 
*[http://southernpolyurethanes.com/Tech%20Sheets/Epoxy%20Primer.htm Southern Polyurethanes Epoxy Primer]
 
*[http://southernpolyurethanes.com/Tech%20Sheets/Epoxy%20Primer.htm Southern Polyurethanes Epoxy Primer]
 +
 +
===Transtar===
 +
*[http://www.tat-co.com/product-files/data-sheets/data-sheet-2k-epoxy-primer-sealer-6131-english-2.pdf 2K Epoxy Primer/Sealer]
  
 
===Valspar===
 
===Valspar===

Latest revision as of 00:24, 31 May 2023

Personal tools
Namespaces
Variants
Actions
Navigation
Categories
Toolbox