Crankshaft Coalition Wiki
| Line 8: | Line 8: | ||
For more info, check out the [[8 sentence quick-start guide]]. For further details, see [[Help:Contents|the help section]]. | For more info, check out the [[8 sentence quick-start guide]]. For further details, see [[Help:Contents|the help section]]. | ||
| + | ==Article categories== | ||
| + | ''Not all articles are categorized.'' | ||
| + | [[Engine articles]], [[ID'ing and decoding articles]], [[Fastener articles]], [[Rearend articles]], [[Suspension/Steering/Brakes articles]], [[Transmission articles]], [[Drivetrain articles]], [[Electrical articles]], [[Garage and shop articles]]. | ||
| + | |||
| + | ==Well-developed articles== | ||
| + | These articles are well on their way, but could always use additional information, photos, or editing. | ||
| + | |||
| + | *[[Body and exterior tips]] | ||
| + | *[[Chrysler Hemi engine]] | ||
| + | *[[John Deere Blitz Black paint]] | ||
| + | *[[Make a fiberglass fan shroud]] | ||
| + | *[[Removing rusted and broken fasteners]] | ||
| + | *[[Steering shaft assemblies from junkyard parts]] | ||
| + | *[[Straightening a rear end housing]] | ||
| + | |||
| + | |||
| + | |||
| + | ==Articles to work on== | ||
| + | These articles are off to a good start, but still need considerable work. Specifically, they could use more information, photos, and general cleanup and organizing. | ||
| + | *[[Automobile Body and Frame Rotisserie]] | ||
| + | *[[Basic stuff for newbies]] | ||
| + | *[[Bulletproof cooling system]] | ||
| + | *[[Buffing your newly-finished paint]] | ||
| + | *[[C-clip eliminator for 8.8 Ford]] | ||
| + | *[[Cadillac engine Knowledge]] | ||
| + | *[[Cheapo paint job]] | ||
| + | *[[Cold air intakes]] | ||
| + | *[[Cylinder Head Choice]] | ||
| + | *[[Early Hemi engine specifications]] | ||
| + | *[[Electric Fuel Pump Mount]] | ||
| + | *[[Epoxy primer]] | ||
| + | *[[First paint job]] | ||
| + | *[[Ford 144-250 inline 6 High performance building]] | ||
| + | *[[General Motors build codes]] | ||
| + | *[[Head gasket]] | ||
| + | *[[Header design]] | ||
| + | *[[Health and Safety in the Shop or Garage]] | ||
| + | *[[Homologation]] | ||
| + | *[[Hot rodding the HEI distributor]] | ||
| + | *[[How do turn signals work?]] | ||
| + | *[[How to document your project]] | ||
| + | *[[How to Find Vacuum Leaks]] | ||
| + | *[[How to find your next project]] | ||
| + | *[[How to identify a Ford V8]] | ||
| + | *[[How to install Mustang II IFS Spindles]] | ||
| + | *[[How to rebuild an engine]] | ||
| + | *[[How to rebuild automotive carburetors]] | ||
| + | *[[How to remove a starter]] | ||
| + | *[[How to solder electrical connections]] | ||
| + | *[[How to title a hot rod]] | ||
| + | *[[How to torque a bolt]] | ||
| + | *[[Idle air control valve overview]] | ||
| + | *[[Long term storage preparation]] | ||
| + | *[[Mopar Rear Axle Spotter's Guide]] | ||
| + | *[[More GM RPO codes]] | ||
| + | *[[NHRA-legal Roll Bar]] | ||
| + | *[[Pitted rust]] | ||
| + | *[[Pre-1980 VIN decoding]] | ||
| + | *[[Rearend removal]] | ||
| + | *[[Rebuild an Alternator]] | ||
| + | *[[Rebuilding an early Hemi engine]] | ||
| + | *[[Removal Of GM Door Panel]] | ||
| + | *[[Rewiring a vehicle]] | ||
| + | *[[Rust]] | ||
| + | *[[Swap Solutions: Driveshafts]] | ||
| + | *[[Swap Solutions: Engines]] | ||
| + | *[[Swap Solutions: Rear Axles]] | ||
| + | *[[Swapping to rack and pinion steering]] | ||
| + | *[[The FREE T Bucket plans]] | ||
| + | *[[Transmission Identification]] | ||
| + | *[[Suspension]] | ||
| + | *[[Why a shorter rear gear will accelerate the car quicker]] | ||
| + | *[[Window removal and installation]] | ||
==Start a new article== | ==Start a new article== | ||
Your Privacy Choices