Bondo
From Crankshaft Coalition Wiki
(→Body filler tips) |
|||
| Line 8: | Line 8: | ||
*[http://solutions.3m.com/wps/portal/3M/en_US/3MAutomotive/Aftermarket/Products/Product-Catalog/?PC_7_RJH9U5230GE3E02LECFTDQCEK3_nid=02PKX0XCK6beFDKXQL309Jgl 3M body fillers and auto body repair products] | *[http://solutions.3m.com/wps/portal/3M/en_US/3MAutomotive/Aftermarket/Products/Product-Catalog/?PC_7_RJH9U5230GE3E02LECFTDQCEK3_nid=02PKX0XCK6beFDKXQL309Jgl 3M body fillers and auto body repair products] | ||
*[http://www.evercoat.com/products.aspx Evercoat] | *[http://www.evercoat.com/products.aspx Evercoat] | ||
| + | *[http://solutions.3m.com/wps/portal/3M/en_US/3MAutomotive/Aftermarket/Products/Product-Catalog/?PC_7_RJH9U5230GE3E02LECFTDQCEK3_nid=MD5SPM1WHRgsFDKXQL309JglF3N1FCNSSKbl Marson Platinum Plus] | ||
=="Waterproof" body fillers== | =="Waterproof" body fillers== | ||
| Line 13: | Line 14: | ||
If using a waterproof paint, a waterproof body filler may be unnecessary anyway. | If using a waterproof paint, a waterproof body filler may be unnecessary anyway. | ||
| + | |||
| + | ==Body filler tips== | ||
| + | In a large flat plastic if or disposable surface Make small batches of well folded body filler, apply small batches in wide thin layers. Sanding and cleaning once partially hardened. This will result in a better finish and smoother transitions. It will also reduce waste; saving money. | ||
| + | *For body lines and peaks on hoods or doors, use a contour gauge to make a custom plastic filler spreader: | ||
| + | #Place the contour gauge on an undamaged area to get the contour. | ||
| + | #Trace the contour onto a plastic body filler spreader. | ||
| + | #Trim out the shape on the spreader. | ||
| + | *Cut filler spreaders to the desired size. | ||
| + | *To clean body filler spreaders, use 1/4 of a 3M scuff pad with lacquer thinner on it. A metal quart can with a lid makes a safe way to store the scuff pad along with some lacquer thinner. | ||
| + | *For reproducing small parts such as gaskets, use plastic body filler to make a mold: | ||
| + | #If the part doesn't already exist, a replica has to be made in its shape (for example, carve it out of soft plastic). | ||
| + | #Apply some wax to the part (this will act as a mold release), and lay it down on a piece of wax paper. | ||
| + | #Mix up some body filler, and place it in a small cup or bowl (the cap on a plastic jug may work). | ||
| + | #While the filler is still wet, place it over the part. | ||
| + | #When the filler hardens, it can be removed and used as a mold. | ||
| + | *When applying body filler upside down, apply the filler to a sheet of thin plastic (such as the side of a milk jug) and press it into place. When the filler hardens, peel the plastic away. | ||
| + | *Use an aluminum ruler to find high and low spots such as doors, hood to fender, trunk lid to fender, etc. | ||
| + | *If using filler with hatonite you can sand filler while still tacky. This will shred the filler smooth easily with hardly any pressure. When finished, follow up with a polyester glaze or add filler thinner to your final coat of filler. | ||
==DIY body filler recipes== | ==DIY body filler recipes== | ||
Your Privacy Choices