Powerglide competition transmissions
From Crankshaft Coalition Wiki
m (oops, dancing monkey goof) |
(Add text; minor clean up) |
||
| Line 4: | Line 4: | ||
[[File:PG dimensions.jpg]]<br style="clear:both"/> | [[File:PG dimensions.jpg]]<br style="clear:both"/> | ||
| − | ==Aftermarket Powerglide cases== | + | ==Aftermarket Powerglide cases== |
| − | [[File:Reid 2-Piece Superglide Transmission Case with SBFord Bellhousing p-n BH010.jpg|thumb|left|300px||Reid Superglide Powerglide case with SB Ford bellhousing mounted]] | + | |
| + | [[File:Reid 2-Piece Superglide Transmission Case with SBFord Bellhousing p-n BH010.jpg|thumb|left|300px||Reid Superglide Powerglide case with SB Ford bellhousing mounted]] | ||
| + | |||
[[File:TCI p-n 720002 Superglide case.jpg|frame|||Dedenbear Powerglide case which are now Reid brand]] | [[File:TCI p-n 720002 Superglide case.jpg|frame|||Dedenbear Powerglide case which are now Reid brand]] | ||
[[File:Ultra case tci.gif|frame|left|JW Ultracase Powerglide]] | [[File:Ultra case tci.gif|frame|left|JW Ultracase Powerglide]] | ||
| Line 11: | Line 13: | ||
==Aftermarket Powerglide bellhousings== | ==Aftermarket Powerglide bellhousings== | ||
| − | Below are bellhousings used to mount the Reid Powerglide transmission case to various engines. From left to right: 4.6/5,4 L Ford Mod motor; SB Mopar; BOP; BB Mopar; Ford 385 series; SB Ford; Chevy. | + | Below are bellhousings used to mount the Reid Powerglide transmission case to various engines. |
| − | [ | + | [[File:Bellhousings Reid Powerglide50-60-30-40-20-10-001.jpg|thumb|left|600px|From left to right: 4.6/5,4 L Ford Mod motor; SB Mopar; BOP; BB Mopar; Ford 385 series; SB Ford; Chevy.]]<br style="clear:both"/> |
| + | |||
| + | ==Forward drum/clutches== | ||
| + | From [http://www.hotrodders.com/forum/glide-10-clutch-forward-drum-220373.html here]: | ||
| + | |||
| + | <blockquote> | ||
| + | ;Glide 10 clutch forward drum downside<br> | ||
| + | </blockquote> | ||
| + | <blockquote> | ||
| + | I have tried to use one of these and had a problem. When they made the drum to accept more clutches (it has to be used with a cut piston and a hub that is deep enough to hold all 10), the pocket the piston fits in is very shallow so it has a LOT less movement available to engauge the clutches. This means the clutch pack has to have a lot less clearance or the piston will extend too far and the outer rubber piston ring will pop out and hang up the piston. </blockquote> | ||
| + | <blockquote> | ||
| + | The piston only has about 0.125" of movement or the ring will pop out. This can be changed about 0.040" by cutting the pads off the back of the stock piston to allow it to sit flat against the back of the pocket. Another problem that can occur on the stock piston (depending on the hub/piston combo used) is interference with the pads on the clutch side of the piston face hitting the deep hub and not allowing the clutch disks to have full pressure. | ||
| + | </blockquote> | ||
| + | <blockquote> | ||
| + | Just because it is made for 10 clutches, doesn't mean you have to use all 10. It can be stacked with as many steels as is needed to make up for using less disks. The more fiber disks you use the greater the drag will be. Six disks will hold 1100 hp with 225 lbs. pressure. | ||
| + | </blockquote> | ||
==Race-prepped Powerglide planetary== | ==Race-prepped Powerglide planetary== | ||
| − | [[ | + | Procedure for assembling a race Powerglide planetary unit. |
| + | |||
| + | ==Tools== | ||
| + | A special fixture that holds the needle bearings in place and provides the correct number of needle bearings by the length of the slot the bearings sit in. | ||
| + | |||
| + | [[file:Pg_planet_02.jpg|frame|none|Fixture holds needle bearings used for each pinion gear, also provides correct count of bearings]] | ||
| + | |||
| + | [[file:Pg_planet_needles05.jpg|frame|none|Custom aluminum pins for assembling planetary gears]] | ||
| + | |||
| + | ==Carrier for planetary== | ||
| + | |||
| + | [[file:Pg_planet_03.jpg|frame|none|Naked carrier bowl that holds the gears in place, thrust washers shown in place]] | ||
| + | |||
| + | [[file:Pg_planet_04.jpg|frame|none|Close up view of thrust washers in place, there are 12 washers on this design carrier]] | ||
| + | |||
| + | ==Assemble bearings in gears== | ||
| + | |||
| + | [[file:Bearing_tool_grease_.jpg|frame|none|Grease applied to aluminum tool, note hardened washer slid on tool first]] | ||
| + | |||
| + | [[file:Pg_planet_needles01.jpg|frame|none| Bearings stick to aluminum tool with assembly grease, with washer in place]] | ||
| + | |||
| + | [[file:Pg_planet_needles02.jpg|frame|none| Slide bearings inside the bore of the gear]] | ||
| + | |||
| + | [[file:Gear_w-needles.jpg|frame|none|Final product gear with needle bearings installed]] | ||
| + | |||
| + | [[file:Pg_planet_t-washer.jpg|frame|none|Long gears in place, bronze thrust washer in bottom of carrier]] | ||
| + | |||
| + | [[file:Pg_planet_gears01.jpg|frame|none|Sun gear with bearing (on top of gear) installed in center position of the carrier]] | ||
| + | |||
| + | [[file:Pg_planet05.jpg|frame|none|Gears all installed, aluminum dowel pins in place to hold the gears in alignment]] | ||
| + | |||
| + | [[file:Pg_planet_pins01.jpg|frame|none|Planetary with pinion pins in place, nearly completed unit]] | ||
[[Category:Transmission]] | [[Category:Transmission]] | ||
[[Category:undeveloped articles]] | [[Category:undeveloped articles]] | ||
| − | {{ | + | [[Category:Undeveloped Transmission articles]] |
| + | {{newarticle1}} | ||
Your Privacy Choices