Editing Building an inline 6 Chevy 250 engine
Line 7: | Line 7: | ||
|} | |} | ||
− | The Chevy inline 6 | + | The Chevy inline 6 has been around in one version or another since 1929 until 1988 in domestic vehicles. The Chevy straight 6 250 cid engine was brought out in 1966. It has a 0.280" longer stroke (3.53") and the same bore (3.875") as the 230 cid straight 6. It boasts a 7 main bearing bottom end- quite an improvement over the previous generation inline's 4 main bearings. |
==Some things to consider== | ==Some things to consider== | ||
− | Building a straight 6 250 is not any harder to do than any other inline 6, be it a Ford or Chevy | + | Building a straight 6 250 is not any harder to do than any other inline 6, be it a Ford or Chevy, GMC, etc. Parts aren't as common for the inline 250 as they are for a SBC, but there is info and quite a few suppliers for parts, as well as places that cater to almost nothing but the Chevy inline 6 engines. |
− | The inline 6 Chevy 250 should not be compared to a SBC engine. Besides the obvious differences, they share practically no parts w/the V8 engines | + | The inline 6 Chevy 250 should not be compared to a SBC engine. Besides the obvious differences, they share practically no parts w/the V8 engines. Because of this fact expect it to cost more per horsepower than a Chevy V8. The reward is this is not a "belly button" engine; instead it is considered "old school" and has cred because of what it ''isn't'' as much as for what it '''is'''. |
To the right person, building a 250 Chevy 6 can be just as rewarding as any other engine, and if parts are selected in a coordinated manner and the engine used in a way that accentuates its strong suits- like dependability and good lower RPM torque production for its size- a very satisfying result can be had. | To the right person, building a 250 Chevy 6 can be just as rewarding as any other engine, and if parts are selected in a coordinated manner and the engine used in a way that accentuates its strong suits- like dependability and good lower RPM torque production for its size- a very satisfying result can be had. | ||
− | It's a fool's mission to build a NA inline 6 like the Chevy 250 expecting to run amok on all the | + | It's a fool's mission to build a NA inline 6 like the Chevy 250 expecting to run amok on all the SBC and SBFs out there. Not only will the results be very humbling, but the amount of money that would need to be spent in order to go toe-to-toe with a SBC 350 will break most people's budget all to hell. So instead of trying to beat the world, it may be much more satisfying to build a Chevy 250 to make around 0.8-1 HP/cid (~200-250 HP), and revel in the uniqueness of it and enjoy as torquey, strong running engine that has a sound and look all of its own. |
− | Given enough time, effort and cash, an inline Chevy 6 can make >/= 2 HP/ | + | Given enough time, effort and cash, an inline Chevy 6 can make >/= 2 HP/ci naturally aspirated and far more than that using a turbocharger. Superchargers can also be used, but the turbo is the preference of many who are going for boost. |
==Engine ID== | ==Engine ID== | ||
===Casting numbers, date codes, and suffix codes=== | ===Casting numbers, date codes, and suffix codes=== | ||
− | Obviously casting numbers and | + | Obviously casting numbers and VIN stampings can be a big help. Chevy inline 6 casting numbers can usually be found just above the starter on the passenger side of the block. |
− | On the block there will be foundry ID codes, for instance "CON3". This is no help in | + | On the block there will be foundry ID codes, for instance "CON3". This is no help in ID'ing the engine. |
There may be a date code cast into the block. Example- "A 30 2": Jan 30 of a year ending in 2. If the engine is a 250, that would be 1972. | There may be a date code cast into the block. Example- "A 30 2": Jan 30 of a year ending in 2. If the engine is a 250, that would be 1972. | ||
Line 30: | Line 30: | ||
The suffix code (also called the "application" code) will be at the end of a string of letters and numbers (that's why it's called a suffix). The suffix string is usually a letter followed by a date code, followed by 1, 2 or 3 letter code. This is found in the area near the distributor, above the fuel pump. The suffix string of letters/numbers are always stamped in, not cast into the block like the date code or foundry ID code. | The suffix code (also called the "application" code) will be at the end of a string of letters and numbers (that's why it's called a suffix). The suffix string is usually a letter followed by a date code, followed by 1, 2 or 3 letter code. This is found in the area near the distributor, above the fuel pump. The suffix string of letters/numbers are always stamped in, not cast into the block like the date code or foundry ID code. | ||
− | There may also be a partial | + | There may also be a partial VIN number stamped in a separate string of numbers near the suffix string. If the block is missing the suffix and partial VIN, there's no way to know what the engine might have come in originally, unless there were other external clues like a carb w/a governor on it (would be on a heavy truck or bus), or if it had a large bellhousing and a HD "granny low" trans (also HD truck/bus application). If the crankshaft has a pilot bushing in it, that would mean it had been used with a manual trans- although this could have been added later.<br> |
See '''[[Building an inline 6 Chevy 250 engine#Resources|below]]''' under '''Resources''' for sites that have casting number info. | See '''[[Building an inline 6 Chevy 250 engine#Resources|below]]''' under '''Resources''' for sites that have casting number info. | ||
===Deck height=== | ===Deck height=== | ||
− | The deck height of the Chevy 230 and 250 inline 6 engines is shorter than the 292 inline 6 engine. That means the | + | The deck height of the Chevy 230 and 250 inline 6 engines is shorter than the 292 inline 6 engine. That means the pushrod cover is shorter on those engines than on the 292 Chevy 6, as seen below. |
{| | {| | ||
|[[File:Vin stamp.jpg|thumb|300px|250 Chevy inline 6. Location of VIN/application code stamping for 1962 and newer engines is circled]] | |[[File:Vin stamp.jpg|thumb|300px|250 Chevy inline 6. Location of VIN/application code stamping for 1962 and newer engines is circled]] | ||
Line 41: | Line 41: | ||
==Cylinder heads== | ==Cylinder heads== | ||
− | The integrated intake head | + | The integrated intake head isn't well suited for performance duty. About all that can be done for a head with this intake, is the 1 barrel can be swapped for a 2 barrel by using an adaptor. Not the hot ticket. The lump port mods along with porting, larger valves, etc. can be done to ANY head, but without the ability to use a high performance intake, these mods would be largely wasted. |
− | Using the earlier head | + | Using the earlier head with the detachable intake from a 194, 230 or 250 cid inline Chevy 6 offers a much better platform. Because of the current lack of aftermarket support for inline Chevy 6 cylinder heads, the hotrodder is left with the removable intake head from the early/mid '70s as the best choice for performance use, unless the cost of a custom head can be justified. |
− | In the past there were heads made for the Chevy 6. Now there are one-off heads for the Chevy inline 6 that have been made from 2 SBC aftermarket aluminum heads that have been divided and welded back together | + | In the past there were heads made for the Chevy 6. Now there are one-off heads for the Chevy inline 6 that have been made from 2 SBC aftermarket aluminum heads that have been divided and welded back together. |
− | A relatively easy to find head to swap on the 250 inline Chevy is casting number 3864883 from a 194 | + | A relatively easy to find head to swap on the 250 inline Chevy is casting number 3864883 from a 194 cid Chevy inline 6 engine. If it's milled 0.060", it will give about 10:1 compression on a Chevy 250 using stock type pistons. |
===One-off custom aluminum head=== | ===One-off custom aluminum head=== | ||
Line 58: | Line 58: | ||
Just goes to show you what can be done with enough skill, tools, time and dedication. | Just goes to show you what can be done with enough skill, tools, time and dedication. | ||
− | [Kay Sissell] has also done some custom heads for the inline Chevy six. He now offers ported cast iron heads and other parts. | + | [http://sissellautomotive.com/ Kay Sissell] has also done some custom heads for the inline Chevy six. He now offers ported cast iron heads and other parts. |
===Intake port mods=== | ===Intake port mods=== | ||
The Chevy 250 head has a "3-port" intake. That means two ports are siamesed into a single port. This design, while fine for a daily driver or truck, leaves a lot to be desired for high performance work. | The Chevy 250 head has a "3-port" intake. That means two ports are siamesed into a single port. This design, while fine for a daily driver or truck, leaves a lot to be desired for high performance work. | ||
− | So it comes as no surprise that improving the intake port flow will help power. A big improvement to the Chevy inline 250 cylinder head is to install an intake port "lump". For years, these were one-off, hand-made pieces that were quite a chore to fabricate and mount. Some were better than others, and some were worse than nothing. Nowadays, [http://t6racing.org/index.html T6 Racing] and [http://www.12bolt.com/home | + | So it comes as no surprise that improving the intake port flow will help power. A big improvement to the Chevy inline 250 cylinder head is to install an intake port "lump". For years, these were one-off, hand-made pieces that were quite a chore to fabricate and mount. Some were better than others, and some were worse than nothing. Nowadays, [http://t6racing.org/index.html T6 Racing] and [http://www.12bolt.com/home Autowerks] have designed a lump kit and can supply all the necessary tools and info to install it. It is cast and machined pieces of metal that fit onto the intake port floors to vastly improve flow. |
{| | {| | ||
Line 72: | Line 72: | ||
|[[File:Top lump port w arrows.jpg|thumb|370px|left|Arrowed area has to be blended away]] | |[[File:Top lump port w arrows.jpg|thumb|370px|left|Arrowed area has to be blended away]] | ||
|[[File:Cutaway lump in port.jpg|thumb|290px|left|Cutaway showing lump in port]] | |[[File:Cutaway lump in port.jpg|thumb|290px|left|Cutaway showing lump in port]] | ||
− | |} | + | |} |
===Head torque specs=== | ===Head torque specs=== | ||
Line 78: | Line 78: | ||
==Intake manifolds== | ==Intake manifolds== | ||
+ | Beginning in the mid-'70s, the inline 6 Chevy got an integrated intake cylinder head similar in design to the Ford Falcon Six. This was a step in the wrong direction for a performance engine- the intake being cast as part of the head means it would take too much work to remove it to be able to use any kind of 4-barrel carb. | ||
− | + | But the detachable intake head can be fitted with a large variety of intake manifolds from the cast iron stocker to custom EFI, IR, 4-barrels, staged 2 barrels, multiple carbs from Stromberg 94/97s to Weber's, to name a few. | |
− | + | ||
− | + | ||
− | + | ||
− | But the detachable intake head | + | |
− | + | ||
− | + | ||
− | The stock intake uses the exhaust manifold to provide heat to the intake, but if aftermarket exhaust headers and/or intake manifolds are used, this feature will be missing | + | The stock intake uses the exhaust manifold to provide heat to the intake, but if aftermarket exhaust headers and/or intake manifolds are used, this feature will be missing. For many applications that will see daily driver duty, an aftermarket intake equipped with hot water heating of the plenum is a plus. |
If making all the power possible is the goal, an intake without hot water heating would be the better choice. | If making all the power possible is the goal, an intake without hot water heating would be the better choice. | ||
Line 111: | Line 106: | ||
==Camshafts== | ==Camshafts== | ||
There are still manufacturers stocking cams for the Chevy inline engines. | There are still manufacturers stocking cams for the Chevy inline engines. | ||
− | *[http://www.iskycams.com/onlinecatalog.html Isky catalog], see pages 126-127 | + | *[http://www.iskycams.com/onlinecatalog.html Isky catalog], see pages 126-127 |
==Timing gears== | ==Timing gears== | ||
− | The Chevy inline 6 uses a pair of gears | + | The Chevy inline 6 uses a pair of gears and no chain to turn the camshaft. There are high performance gear sets available from Comp and others. The cam gear on aftermarket performance timing sets is often aluminum. |
==Exhaust manifolds== | ==Exhaust manifolds== | ||
Line 147: | Line 142: | ||
*[http://www.cliffordperformance.net/index.html Clifford Performance] | *[http://www.cliffordperformance.net/index.html Clifford Performance] | ||
*[http://sissellautomotive.com/ Sissells Automotive] | *[http://sissellautomotive.com/ Sissells Automotive] | ||
− | *[http://www.12bolt.com/ | + | *[http://www.12bolt.com/250292_products Autowerks] |
{{youcanedit}} | {{youcanedit}} | ||
[[Category:Engine]] | [[Category:Engine]] | ||
[[Category:GM]] | [[Category:GM]] |