Vortec plastic timing cover replacement
From Crankshaft Coalition Wiki
(→Vortec block) |
|||
| Line 25: | Line 25: | ||
A block using a steel cover uses dowel pins in the block, and has the locating holes in steel cover. | A block using a steel cover uses dowel pins in the block, and has the locating holes in steel cover. | ||
| − | The Vortec block (right) does not use block mounted dowels to locate the cover. Instead, it has holes for the plastic cover's locating pins. The locating holes in the 880 block are >15/64" and <1/4", which is about right for a press-fit 1/4" dowel pin. That said, it's not presently known if the hole size is correct for a press fit solid steel dowel like used on the earlier blocks. As a precaution, the hole should be carefully measured before driving in a solid dowel to avoid cracking the casting. Another alternative is to use a 0.250" OD hollow roll pin to avoid stressing the casting. | + | The Vortec block (right) does not use block mounted dowels to locate the cover. Instead, it has holes for the plastic cover's locating pins. The locating holes in the 880 block are >15/64" and <1/4", which is about right for a press-fit 1/4" dowel pin. That said, it's not presently known if the hole size is correct for a press fit solid steel dowel like used on the earlier blocks. As a precaution, the hole should be carefully measured before driving in a solid dowel to avoid cracking the casting. Another alternative is to use a 0.250" OD hollow roll pin to avoid stressing the casting. Also the timing cover flange is thicker - 5.7L cylinder blocks with the #880 casting will accept early and late timing covers. |
| − | The 880 Vortec block shown has all the holes present and tapped. This is not always the case; some blocks (those used with the 1996-02 C/K truck and vans to 2002 with the exception of those used for marine or industrial applications) are missing two holes and will need to use a gasket as a template to drill and tap the missing holes. (These blocks with the 2 undrilled timing cover holes will also have the water pump bypass hole and its corresponding hole on the RH block deck undrilled.) The thread size is 1/4-20 (1/4" coarse), the pilot hole can be drilled with a #7 bit. | + | The 880 Vortec block shown has all the holes present and tapped. This is not always the case; some blocks (those used with the 1996-02 C/K truck and vans to 2002 with the exception of those used for marine or industrial applications) are missing two holes and will need to use a gasket as a template to drill and tap the missing holes. (These blocks with the 2 undrilled timing cover holes will also have the water pump bypass hole and its corresponding hole on the RH block deck undrilled. Drilling the hole for the water pump bypass requires the use of a water pump gasket as a template (RH water pump hole) and a pre-Vortec head gasket (the hole is drilled at an angle). Fuel pump mounting boss area is usually unmachined (as with the previous 638 or 727 castings where the fuel pump pushrod hole is undrilled even if a factory blockoff plate was used). The timing cover bolt thread size is 1/4-20 (1/4" coarse), the pilot hole can be drilled with a #7 bit. |
==Gaskets and seals== | ==Gaskets and seals== | ||
| Line 43: | Line 43: | ||
[[File:DAMPER COMPARO GEN I to 1-PC RMS2.jpg]] | [[File:DAMPER COMPARO GEN I to 1-PC RMS2.jpg]] | ||
| + | |||
| + | ===Vortec Reluctor Wheels=== | ||
| + | The Vortec reluctor wheels are either 4x (L31 or L29) or 24x (L21) signal type that measure 4.00" in diameter with an overall thickness (height) of 0.410" and have a flange thickness of 0.100" for the small block and 0.200 for the big block. The flange thickness needs to be considered when adding or removing the reluctor as it will change the crank pulley position. | ||
<br><br> | <br><br> | ||
Your Privacy Choices