Valve train geometry
From Crankshaft Coalition Wiki
(Add pdf's) |
(→Things that can effect pushrod length: grammar correction) |
||
| Line 18: | Line 18: | ||
===Chevy small block=== | ===Chevy small block=== | ||
*Stock hydraulic flat tappet SBC- 7.8” | *Stock hydraulic flat tappet SBC- 7.8” | ||
| − | *SBC OEM hydraulic roller pushrods are 7.2” long. When using shorter | + | *SBC OEM hydraulic roller pushrods are 7.2” long. When using shorter GM OEM roller lifters from the 3.1L or 3.4L V6, or the 2.2L inline 4 cylinder engines, start with 7.500" pushrods. These lifters are mostly only used when converting a flat tappet block to use an OEM roller cam, although they might be an advantage in a roller block due to their lighter weight. |
*Crane retro hydraulic roller- 7.046" | *Crane retro hydraulic roller- 7.046" | ||
*Retrofit roller lifter pushrods are 7.300". | *Retrofit roller lifter pushrods are 7.300". | ||
| Line 25: | Line 25: | ||
Stock pushrod length- 9.130". It has been published that if using Chevy lifters, the pushrod length is 9.290” as a starting point. However, caution must be used if Chevy lifters are going to be tried in a Pontiac engine because the oil band is in a different location. This could effect oiling. There are aftermarket lifters advertised for use in both Chevy and Pontiac engines. These should also be checked but the assumption is that the oil band is correctly located for both applications. | Stock pushrod length- 9.130". It has been published that if using Chevy lifters, the pushrod length is 9.290” as a starting point. However, caution must be used if Chevy lifters are going to be tried in a Pontiac engine because the oil band is in a different location. This could effect oiling. There are aftermarket lifters advertised for use in both Chevy and Pontiac engines. These should also be checked but the assumption is that the oil band is correctly located for both applications. | ||
| − | ==Things that can | + | ==Things that can affect pushrod length== |
A large number of variables are involved in determining the correct length pushrod for your application. Pushrod length is affected by any of the following: | A large number of variables are involved in determining the correct length pushrod for your application. Pushrod length is affected by any of the following: | ||
| Line 45: | Line 45: | ||
*[http://www.hotrodders.com/forum/mid-lift-rockers-206836.html?highlight=MID+LIFT+MILLER Miller mid lift rocker theory] | *[http://www.hotrodders.com/forum/mid-lift-rockers-206836.html?highlight=MID+LIFT+MILLER Miller mid lift rocker theory] | ||
*[http://www.hotrodders.com/forum/rocker-arm-199353.html Rocker arm geometry] | *[http://www.hotrodders.com/forum/rocker-arm-199353.html Rocker arm geometry] | ||
| + | |||
| + | ;Example of instructions for Miller Mid-Lift PA Series rockers | ||
| + | *[[Media:Miller pg 1.png|Page 1]] | ||
| + | *[[Media:Miller pg 2.png|Page 2]] | ||
==Tools== | ==Tools== | ||
[[File:PUSH ROD LENGTH CHECKING TOOL 004.JPG|thumb|left|400px|Homemade adjustable pushrod length checking tool]] | [[File:PUSH ROD LENGTH CHECKING TOOL 004.JPG|thumb|left|400px|Homemade adjustable pushrod length checking tool]] | ||
<br style="clear:both"/> | <br style="clear:both"/> | ||
| + | |||
| + | [http://www.homemadetools.net/forum/adjustable-push-rod-length-checker-5 Instructions] for making an adjustable pushrod length checker. | ||
| + | |||
| + | Other homemade pushrod length checking tools at [http://www.homemadetools.net/tag/push-rod HomemadeTools.net] | ||
| + | |||
Miller uses a MID-LIFT G-TooL to measure for geometry. It is quite different from the other devices on the market, like from Comp Cams and others that are used to estimate pushrod length. | Miller uses a MID-LIFT G-TooL to measure for geometry. It is quite different from the other devices on the market, like from Comp Cams and others that are used to estimate pushrod length. | ||
Your Privacy Choices