TH350 rebuild tech
From Crankshaft Coalition Wiki
(→Rear planetary unit install) |
(→Reference material) |
||
| Line 146: | Line 146: | ||
[[File:T-350_ring_gear_with_washer.jpg|thumb|300px|left|Front ring gear with 3-tang thrust washer in place installed into case on front planet]] <br style="clear:both"/> | [[File:T-350_ring_gear_with_washer.jpg|thumb|300px|left|Front ring gear with 3-tang thrust washer in place installed into case on front planet]] <br style="clear:both"/> | ||
| − | ==Direct drum assembly== | + | ==T-350 Direct drum assembly== |
For racing and heavy towing use, you will want to machine the direct clutch piston down approximately 0.160" to allow for one extra friction and steel plate for a total of 5 frictions, and 5 steels in the directs. This can be accomplished on a brake lathe. | For racing and heavy towing use, you will want to machine the direct clutch piston down approximately 0.160" to allow for one extra friction and steel plate for a total of 5 frictions, and 5 steels in the directs. This can be accomplished on a brake lathe. | ||
| Line 153: | Line 153: | ||
If the piston is too low, the bottom flat steel plate can drop below the grooves in the drum and bind up the piston. You can leave out center cushion seal if dual feed is used. | If the piston is too low, the bottom flat steel plate can drop below the grooves in the drum and bind up the piston. You can leave out center cushion seal if dual feed is used. | ||
| − | [[File:T-350_direct_piston.jpg|thumb|300px|left| | + | [[File:T-350_direct_piston.jpg|thumb|300px|left|T-350 direct clutch drum pistons, piston on left cut for 5 friction use]] <br style="clear:both"/> |
| − | Heavy duty applications should also get a heat treated intermediate sprag race. The heat treatment makes the race less brittle. A heat treated intermediate sprag race is darker colored than a stock part. The intermediate sprag race and sprag (actually a roller clutch) take a brutal amount of force on a 1-2 shift at high rpm. Even more so with harsher shift calibrations. It is the single weakest part of a TH350. This is not to say a TH350 is not tough; they can reliably handle power in the 600 HP or lb/ft range if properly assembled using the right parts. | + | Heavy duty applications should also get a heat treated intermediate sprag race. The heat treatment makes the race less brittle. A heat treated intermediate sprag race is darker colored than a stock part. The T-350 intermediate sprag race and sprag (actually a roller clutch) take a brutal amount of force on a 1-2 shift at high rpm. Even more so with harsher shift calibrations. It is the single weakest part of a TH350. This is not to say a TH350 is not tough; they can reliably handle power in the 600 HP or lb/ft range if properly assembled using the right parts. |
[[file:TH350intspragraces.jpg]] | [[file:TH350intspragraces.jpg]] | ||
| Line 163: | Line 163: | ||
Several companies offer an even heavier duty direct drum/sprag assembly. It uses a 36 element sprag (similar to what is used in the TH400) and a machined drum; it will withstand more torque than a stock unit or one with just a hardened race. These units can cost $300.00 or more. | Several companies offer an even heavier duty direct drum/sprag assembly. It uses a 36 element sprag (similar to what is used in the TH400) and a machined drum; it will withstand more torque than a stock unit or one with just a hardened race. These units can cost $300.00 or more. | ||
| − | [[File:T-350_HD_drum_sprag.jpg|thumb|300px|left| | + | [[File:T-350_HD_drum_sprag.jpg|thumb|300px|left|T-350 direct clutch drum with 36 element sprag]] <br style="clear:both"/> |
| Line 170: | Line 170: | ||
The parts go on the direct drum. | The parts go on the direct drum. | ||
| − | [[File:T-350 drum sprag race.jpg|thumb|300px|left| | + | [[File:T-350 drum sprag race.jpg|thumb|300px|left|T-350 direct clutch drum with sprag, race, retainer]] <br style="clear:both"/> |
Assembled direct drum sprag and race with retainer. | Assembled direct drum sprag and race with retainer. | ||
| − | [[File:T-350_drum_sprag_assembled.jpg|thumb|300px|left| | + | [[File:T-350_drum_sprag_assembled.jpg|thumb|300px|left|T-350 direct clutch drum with assembled sprag, race, retainer]] <br style="clear:both"/> |
| − | The direct drum should use a wider bushing even on stock rebuilds. Stock is 0.500" a wider 0.750" is available in some bushing kits. Most bushing kits include the wide one. There is a lot of load on this bushing, and it should ALWAYS be replaced on overhaul. | + | The T-350 direct drum should use a wider bushing even on stock rebuilds. Stock is 0.500" a wider 0.750" is available in some bushing kits. Most bushing kits include the wide one. There is a lot of load on this bushing, and it should ALWAYS be replaced on overhaul. |
| − | [[File:TH350directbushings1.jpg|thumb|300px|left|The direct drum should use a wider bushing even on stock rebuilds]] <br style="clear:both"/> | + | [[File:TH350directbushings1.jpg|thumb|300px|left|The T-350 direct drum should use a wider bushing even on stock rebuilds]] <br style="clear:both"/> |
Also check the inside bore of the drum for wear from the sealing rings. A small amount of wear can be honed out. Visual shiny spots with no detectable wear are acceptable. | Also check the inside bore of the drum for wear from the sealing rings. A small amount of wear can be honed out. Visual shiny spots with no detectable wear are acceptable. | ||
| − | [[File:T-350_direct_drum_bushing.jpg|thumb|300px|left|Direct drum with wide bushing, piston, springs and retainer installed]] <br style="clear:both"/> | + | [[File:T-350_direct_drum_bushing.jpg|thumb|300px|left|T-350 Direct drum with wide bushing, piston, springs and retainer installed]] <br style="clear:both"/> |
Next you will install the direct piston lip seals, and install the piston in the drum. Take note of the orientation of the seals, the lip will face towards the "oil" side of the piston, not the clutch side. | Next you will install the direct piston lip seals, and install the piston in the drum. Take note of the orientation of the seals, the lip will face towards the "oil" side of the piston, not the clutch side. | ||
| − | Below is a high performance | + | Below is a high performance T-350 piston for a drum without a center seal that would separate the two halves of the direct piston. |
| − | [[File:TH350directpistonseals1.jpg|thumb|300px|left|Direct piston with lip seals installed]] <br style="clear:both"/> | + | [[File:TH350directpistonseals1.jpg|thumb|300px|left|T-350 Direct piston with lip seals installed]] <br style="clear:both"/> |
==Dual feeding== | ==Dual feeding== | ||
| Line 248: | Line 248: | ||
Intermediate piston installed. | Intermediate piston installed. | ||
| − | [[File:T-350_pump_n_piston.jpg|thumb|300px|left| | + | [[File:T-350_pump_n_piston.jpg|thumb|300px|left|T-350 pump with intermediate piston installed]]<br style="clear:both"/> |
| − | Sealing rings on the pump stator. Remove the second ring from the bottom if dual feeding. | + | Sealing rings on the T-350 pump stator. Remove the second ring from the bottom if dual feeding. |
[[File:T-350_stator_rings.jpg|thumb|300px|left|Sealing rings on pump]] <br style="clear:both"/> | [[File:T-350_stator_rings.jpg|thumb|300px|left|Sealing rings on pump]] <br style="clear:both"/> | ||
| Line 258: | Line 258: | ||
Pump gear install. Note the orientation of the tangs on the inner gear. They are offset. They should face away from the seal. Incorrect installation will result in pump failure and converter damage. | Pump gear install. Note the orientation of the tangs on the inner gear. They are offset. They should face away from the seal. Incorrect installation will result in pump failure and converter damage. | ||
| − | [[File:T-350_pump_half.jpg|thumb|300px|left|Notice inner pump gear tangs, they must be '''up''' as seen here]] <br style="clear:both"/> | + | [[File:T-350_pump_half.jpg|thumb|300px|left|Notice the T-350 inner pump gear tangs, they must be '''up''' as seen here]] <br style="clear:both"/> |
| Line 413: | Line 413: | ||
=Reference material= | =Reference material= | ||
| − | [[File:Sessions- ATSG-Haynes manuals.jpg|thumb|600px|left|Left to right: [http://www.amazon.com/Turbo-Hydra-Matic-350-Handbook-Sessions/dp/0895860511 Turbo Hydra-Matic 350 Handbook] by Ron Sessions; [http://www.northernautoparts.com/ProductModelDetail.cfm?ProductModelId=786 ATSG manual] p/n 44400; Haynes [http://www.amazon.com/gp/product/1563924234/ref=pd_lpo_k2_dp_sr_1?pf_rd_p=486539851&pf_rd_s=lpo-top-stripe-1&pf_rd_t=201&pf_rd_i=0895860511&pf_rd_m=ATVPDKIKX0DER&pf_rd_r=0J4A1QHT1Y8B032P3Z6P GM Automatic Transmission Overhaul] manual, p/n 10360.]] | + | [[File:Sessions- ATSG-Haynes manuals.jpg|thumb|600px|left|Left to right: [http://www.amazon.com/Turbo-Hydra-Matic-350-Handbook-Sessions/dp/0895860511 Turbo Hydra-Matic 350 Handbook] by Ron Sessions; [http://www.northernautoparts.com/ProductModelDetail.cfm?ProductModelId=786 ATSG manual] p/n 44400; Haynes [http://www.amazon.com/gp/product/1563924234/ref=pd_lpo_k2_dp_sr_1?pf_rd_p=486539851&pf_rd_s=lpo-top-stripe-1&pf_rd_t=201&pf_rd_i=0895860511&pf_rd_m=ATVPDKIKX0DER&pf_rd_r=0J4A1QHT1Y8B032P3Z6P GM Automatic Transmission Overhaul] manual, p/n 10360.]] <br> |
| − | <br> | + | |
| − | |||
[[Category:GM]] | [[Category:GM]] | ||
Your Privacy Choices