Editing Remote Ford solenoid for GM- no hot start
(
diff
)
← Older revision
|
Latest revision
(
diff
) |
Newer revision →
(
diff
)
Jump to:
navigation
,
search
'''Preamble''' Have you ever pulled in to the local Stop 'N Go, shut your engine off, only to come out a few minutes later, hit the key and it wouldn't turn over, let alone start? The problem that you are experiencing is called "heat soak". It is a condition where the heat from the engine and exhaust headers heat up the starter housing, solenoid, and wiring by way of convection. If you have another vehicle, a jump start with booster cables will usually crank it over for you. So why does that make a difference? We'll show you how. '''Electrical Connection Diagram''' [[Image:Ford_sol_on_gm_strtr_blue.jpg]] Note: If you want to keep your vehicle all GM then use a Standard U939 solenoid like the one pictured here: [[Image:Standard_PN_U939.jpg ]] '''THIS IS THE ORIGINAL GM WIRING CONFIGURATION''' The battery wire to the solenoid in the stock configuration is hot at all times. The sequence of events that happens in the standard GM when you hit the starter is as follows; 1. The electricity has to go from the starter switch through the loom to the neutral safety switch. 2. If you are in park (or neutral) the electricity then goes through the loom to the stock solenoid "s" terminal. 3. When the "s" terminal goes hot, it energizes the solenoid. This causes the plunger to throw the starter gear out to the ring gear (flywheel). It also closes an internal set of contacts that sends electricity to the starter motor and also to the "i" terminal. 4. The starter motor doesn't get power until the solenoid contacts are closed. The wire from the "i" terminal is a ballast resistor bypass for the coil. It gives a solid 12 volts to the coil during cranking. Here is where a problem is encountered. It takes a fair amount of current to energize the stock solenoid when hot. Due to the amount of resistance in the wiring set-up, it may not be possible to supply the required current. This is where the Ford solenoid comes into play. '''THIS IS THE MODIFIED WIRING WITH THE FORD SOLENOID''' If you are running an HEI distributor, don't worry about wiring to "i" terminals. 1. The wire that goes to the "s" terminal on the GM solenoid (closest to the block) is removed and wired to the "s" terminal on the Ford solenoid. 2. The wire that goes to the "i" terminal on the GM solenoid (farthest from the block) is removed and wired to the "i" terminal on the Ford solenoid. The "i" terminal on the GM solenoid will not be used. When you purchase the Ford solenoid, make sure that it has the "i" terminal if required for non-HEI distributors. 3. The battery cable is removed from the GM solenoid and is put on one of the large terminals on the Ford solenoid. 4. A battery cable is run from the other large terminal on the Ford solenoid to the large terminal on the GM solenoid. 5. Also on the large terminal on the GM solenoid, you have to add a heavy gauge (10 gauge) wire to the "s" terminal on the GM solenoid. Now, this is what happens when you hit the start switch; 1. The electricity from the starter switch only has to energize the Ford solenoid (that is mounted in a relatively cool location). 2. The "battery" cable to the GM solenoid goes hot. The Ford "i" terminal also goes hot, providing non-ballast voltage to the coil. 3. The GM solenoid now gets a solid "high capacity" current supply and works the plunger and contacts. The internal contacts send voltage to the starter motor. There are a few things that should be noted. This set-up DOES NOT make the GM solenoid any cooler. It just gives it a better current supply. Anything that can be done to shield the starter from the header heat would be beneficial. There are several heat shields on the market and even GM makes one. Always be sure that any wiring doesn't come in contact with the exhaust pipes and use heat socks, available from Jegs or Summit, just in case contact may occur.
|
Editing help
(opens in new window)
Template:Note1
(
edit
)
Personal tools
140.248.77.76
Talk for this IP address
Log in / create account
Namespaces
Page
Discussion
Variants
Views
Read
Edit
View history
Actions
Search
Navigation
Main Page
Recent changes
Random page
Help
All articles
Start a new article
Hotrodders forum
Categories
Best articles
Body and exterior
Brakes
Cooling
Electrical
Engine
Fasteners
Frame
Garage and shop
General hotrodding
Identification and decoding
Interior
Rearend
Safety
Steering
Suspension
Tires
Tools
Transmission
Troubleshooting
Wheels
Toolbox
What links here
Related changes
Special pages
Terms of Use
Copyright
Privacy Policy
Your Privacy Choices
Manage Consent