Pontiac V8 engine

Jump to: navigation, search
m (Pilot bearing (rolling element-type): minor clean up)
m (Minor clean up)
Line 699: Line 699:
 
==Timing covers==
 
==Timing covers==
 
The following is from [http://forums.highperformancepontiac.com/70/6720258/the-general-discussion/water-pumps/#ixzz23bpSfjpr High Performance Pontac forums]:
 
The following is from [http://forums.highperformancepontiac.com/70/6720258/the-general-discussion/water-pumps/#ixzz23bpSfjpr High Performance Pontac forums]:
<blockquote>All of the timing chain covers from 1964 to 1979 will bolt up and interchange with any motor from those years. However, you must use the matching water pump, pulley and crank pulley to avoid alignment problems with the alternator and/or power steering pump. All of the water pumps from ‘64-‘68 will interchange. These pumps have eight bolts and measure 3-5/8” long (from base to water pump pulley flange). The casting number for ‘64-‘65 is 9772716 and for ‘66-‘68 it is 4782482. The matching pulleys are 2” in height. From ‘64-‘67 Pontiac used a small diameter (5.25”) six bolt two-piece harmonic damper and from 68-79 a large diameter (6.75”), one piece four bolt damper was used. In ’69 Pontiac changed to an 11-bolt water pump but the early ’69 was different from late ’69-on. Many early ’69 Firebirds and GTO's used a pump that measured 4” long (casting# 9796351) and the pulley was 2-1/4” in height. From late ’69 to ’79 only one pump style was used, it measured 4-1/2” long and there are at least two different casting numbers used: 482138 and 488296. The matching pulley should measure 2-5/8” in height. Always use the correct diameter and style crank pulley to match the water pump pulley and also use the same series timing chain cover and balancer to properly line up your timing marks. The same timing chain cover was used for both ‘64 & ‘65 and had just a simple pointer. These were cast with number 9773371. The timing cover used on ’66 and ’67 employed a small timing scale marked -4, 0, and +6 and is otherwise identified as casting # 9783130. The ’68, ’69 and ’70 timing covers look very similar with timing marks of 0-6-12 degrees BTDC and accommodated the large diameter damper. The ’68 timing cover casting number is 9790347 and uses the 8-bolt water pump. The ’69-‘70 timing cover casting number is 9796346 and uses the improved 11-bolt pump. For ’71 and later the timing cover timing tab is marked from 4 degrees after to 12 degrees BTDC and is graduated all the way to 16 degrees BTDC. As compression ratios were lowered to 8:1 and lower there became a need for increased initial advance. Casting number for this cover is 482883. If you need to order a water pump the Federal Mogul part numbers are: ‘64-’68 is FP1388N, early ’69 is FP1409N and late ’69-on is FP1423.   
+
<blockquote>All of the timing chain covers from 1964 to 1979 will bolt up and interchange with any motor from those years. However, you must use the matching water pump, pulley and crank pulley to avoid alignment problems with the alternator and/or power steering pump. All of the water pumps from '64-'68 will interchange. These pumps have eight bolts and measure 3-5/8" long (from base to water pump pulley flange). The casting number for '64-'65 is 9772716 and for '66-'68 it is 4782482. The matching pulleys are 2" in height. From '64-'67 Pontiac used a small diameter (5.25") six bolt two-piece harmonic damper and from '68-'79 a large diameter (6.75"), four bolt one-piece damper was used. In '69 Pontiac changed to an 11-bolt water pump but the early '69 was different from late '69-on. Many early '69 Firebirds and GTOs used a pump that measured 4" long (casting #9796351) and the pulley was 2-1/4" in height. From late '69 to '79 only one pump style was used, it measured 4-1/2" long and there are at least two different casting numbers used: 482138 and 488296. The matching pulley should measure 2-5/8" in height. Always use the correct diameter and style crank pulley to match the water pump pulley and also use the same series timing chain cover and balancer to properly line up your timing marks. The same timing chain cover was used for both '64 and '65 and had just a simple pointer. These were cast with number 9773371. The timing cover used on '66 and '67 employed a small timing scale marked -4-0-+6 and is otherwise identified as casting #9783130. The '68, '69 and '70 timing covers look very similar with timing marks of 0-6-12 degrees BTDC and accommodated the large diameter damper. The '68 timing cover casting number is 9790347 and uses the 8-bolt water pump. The '69-'70 timing cover casting number is 9796346 and uses the improved 11-bolt pump. For '71-up the timing cover timing tab is marked from 4 degrees ATDC to 12 degrees BTDC and is graduated all the way to 16 degrees BTDC. As compression ratios were lowered to 8:1 and less there became a need for increased initial advance. Casting number for this cover is 482883. If you need to order a water pump the Federal Mogul part numbers are: '64-'68 is FP1388N, early '69 is FP1409N and late '69-on is FP1423.   
 
</blockquote>
 
</blockquote>
  

Revision as of 14:14, 5 January 2013

Personal tools
Namespaces
Variants
Actions
Navigation
Categories
Toolbox