Body and exterior tips

Jump to: navigation, search
(Assembly and disassembly)
(about online gambling|pediatic!!!)
Line 51: Line 51:
 
excellent resource, http://ycfcfat.ibnsites.com/redpubic67/index.html red pubic hair pictures,  mza,
 
excellent resource, http://ycfcfat.ibnsites.com/redpubic67/index.html red pubic hair pictures,  mza,
  
==Miscellaneous==
+
*To paint rims without scratching them:
+
http://richinnyd.phreesite.com/nursing6262.html contemporary nursing agency
#Mount the tire on the rim, but don't fill it up with air.
+
http://richinnyd.phreesite.com/nursing4846.html rehabilitation nursing
#Mask the tire with paper, stuffing it in between the tire and the rim.
+
http://richinnyd.mycyberway.com/nursing6308.html do it yourself bankruptcy canada
#Paint the rim. You can paint around the back edge of the rim, along with the rest of it.
+
http://richinnyd.mycyberway.com/nursing9568.html home in island long nursing
#Remove the masking and inflate the tire. It will look like the tire was off the rim when it was painted.
+
http://richinnyd.mycyberway.com/nursing2679.html how do i get a masters degree in nursing
*To clean foam buffing pads while using them, use a cheap paint brush with the bristles cut off about halfway for stiffness.
+
http://richinnyd.mycyberway.com/nursing2387.html bankruptcy to avoid paying restitution
*Allow plenty of air circulation around your air compressor. Put it outside if possible, or point a fan at it.
+
http://richinnyd.mycyberway.com/nursing4483.html accredited college degree online vermont
*Make paper templates for easy cutting and drilling. For more information and photos, see Brian Martin's article posted on the Hotrodders Bulletin Board: [http://www.hotrodders.com/forum/tip-day-13-a-71092.html Templates for accurate cutting and drilling].
+
http://richinnyd.mycyberway.com/nursing50.html www bankruptcy co uk
*Before installing weld-on parts (core supports, quarter panels, rear panels, etc.), scuff the inside areas. It's easier to do this before parts are installed.
+
http://richinnyd.mycyberway.com/nursing1800.html bankruptcy secured loans
*For doing small touchups without ending up with a huge repair area from sanding, cut sanding discs down to size.
+
http://richinnyd.mycyberway.com/nursing9762.html jersey job new nursing
*To remove creases and dents from plastic bumpers, heat them with a heat gun, and work the area while it's hot. A wallpaper seam roller can be used to work dents out from the back side of the bumper, and a window screen bead installer can be used to push creases down from the front. Flex filler can be used for finishing.
+
http://richinnyd.mycyberway.com/nursing9185.html agency nursing spectrum
*When chemical stripping parts with heavy buildup:
+
http://richinnyd.mycyberway.com/nursing3167.html journal of advanced nursing practice
#Coat the panel heavily with stripper.
+
http://richinnyd.mycyberway.com/nursing168.html care home in iv mapping nursing therapy
#Cover with a cheap plastic drop cloth, or plastic wrap.
+
http://richinnyd.hostaim.com/nursing8634.html admission criterion home lmrp nursing
#Let it stay covered at least an hour, but as long as overnight.
+
http://richinnyd.hostaim.com/nursing4826.html nursing programs in nc
#The stripper penetrates deeper when it won't dry out, and the plastic wrap makes it easier to remove.
+
http://richinnyd.hostaim.com/nursing8197.html nursing jobs in hospice
*If you want an entire part painted, finish it before installing it. Then, touch it up after it's been welded on. Although, this has been argued to be inefficient on a production basis, especially for parts that are not visible, and have been e-coated for adequate protection.
+
http://richinnyd.hostaim.com/nursing3805.html st. louis nursing home abuse lawyer
*Be creative when sourcing patch metal. Potential sources include:
+
http://richinnyd.hostaim.com/nursing2806.html nursing job search engine
**old refrigerators
+
http://richinnyd.hostaim.com/nursing79.html quality care nursing home
**old air conditioning units
+
http://richinnyd.hostaim.com/nursing2764.html medicaid for nursing homes
**old computer cases
+
http://richinnyd.hostaim.com/nursing103.html quantitative study in nursing
**fenders, roofs, or other body parts from vehicles
+
http://richinnyd.hostaim.com/nursing6012.html cccs or bankruptcy
*Use florescent "drop" lights, rather than incandescent. They create less heat, last longer, and are more resistant to shocks than incandescent bulbs.
+
http://richinnyd.hostaim.com/nursing2647.html care floor home nursing
*Save old magnets that are being thrown away (from old car speakers, or refrigerator/freezer sealing strips, computer hard drives, etc.). They have many uses:
+
http://richinnyd.hostaim.com/nursing6374.html casino casino gambling online
#Place magnets over masking material to keep from blowing around.
+
http://richinnyd.hostevo.com/nursing7565.html fha bankruptcy loans
#Use magnets to hold fire blankets in place while welding.
+
http://richinnyd.hostevo.com/nursing559.html home health care nursing twinfind
#Use a magnet in a plastic bag to pick up nails and screws. When done, turn the bag inside out; the metal parts are in the bag, and the magnet stays clean.
+
http://richinnyd.hostevo.com/nursing8377.html bankruptcy lawyer in atlanta
#Put large magnets along the outside of a tool box, and tools can be suspended from the inside of the box.
+
http://richinnyd.hostevo.com/nursing3893.html online bachelor engineering degree
*Oil filter shells can be used for making recessed tail lights. They come in many different sizes, and the larger ones for commercial trucks may be especially useful.
+
http://richinnyd.hostevo.com/nursing628.html bankruptcy illinois lawyer wheaton
*To make a custom body grommet, use a section of vacuum hose that's been split down the middle with a razor or similar tool. A photo of this can be seen here: [http://hotrodders.com/gallery/showphoto.php/photo/17678/size/big/cat/500/page/ Hotrodders Photo Gallery].
+
http://richinnyd.hostevo.com/nursing3878.html ct nursing geriatric standards of practice
*To pull weld studs easier than the pullers can that come with the cheap weld stud guns, weld a pair of vicegrips to a regular dent puller. They can be tack welded to a screw-on accessory and used as a new attachment.
+
http://richinnyd.hostevo.com/nursing2169.html nursing articles on copd
 +
http://richinnyd.hostevo.com/nursing6340.html travel nursing jobs in hawaii
 +
http://richinnyd.hostevo.com/nursing5032.html online graduate degree wolcott vermont
 +
http://richinnyd.hostevo.com/nursing4036.html accredited online degrees and universities
 +
http://richinnyd.hostevo.com/nursing9208.html nj chapter 7 bankruptcy
  
 
==Questionable or disputed tips==
 
==Questionable or disputed tips==

Revision as of 12:20, 25 July 2008

Personal tools
Namespaces
Variants
Actions
Navigation
Categories
Toolbox