Body and exterior tips
From Crankshaft Coalition Wiki
(→Handling and storing paints, finishes, and related products) |
(→Handling and storing paints, finishes, and related products) |
||
| Line 1: | Line 1: | ||
| − | {{ | + | {{needspics}} |
== Paint and spray guns== | == Paint and spray guns== | ||
===Handling and storing paints, finishes, and related products=== | ===Handling and storing paints, finishes, and related products=== | ||
| − | *When opening a can of paint, punch a | + | *When opening a can of paint, punch a hole in the trough where the lid sits. That way excess paint will drain out of the trough and into the can, rather than splattering when placing the lid back on the can. |
*Buy a set of inexpensive spatulas to use as scrapers for paint cans. | *Buy a set of inexpensive spatulas to use as scrapers for paint cans. | ||
| − | *To preserve hardener | + | *To preserve hardener displace the air in the can with inert gas, such as that from a welding tank. Or, use a commercial inert gas finish preservative such as [http://www.bloxygen.com/ Bloxygen]. |
*Paint and related finishing products can be mixed in glass measuring cups, medicine cups, soup cans, or shot glasses. However, [http://www.ezmix.com EZ Mix] cups are generally preferred for ease of use. Containers with measurements on the side are generally most useful. Be aware that if you use a container with tapered sides you cannot use a paint mixing stick, as this changes the mixing ratio as the cup gets larger towards the top. Paint sticks are only to be used in containers with straight sides. Paper cups are cautioned against because some may have a wax coating. Similarly, plastic cups or containers (medicine cups, yogurt containers, cleaned bottle caps, etc.) are also cautioned against. There are many different kinds of plastic, some of which are inappropriate for storing certain types of finishing products. | *Paint and related finishing products can be mixed in glass measuring cups, medicine cups, soup cans, or shot glasses. However, [http://www.ezmix.com EZ Mix] cups are generally preferred for ease of use. Containers with measurements on the side are generally most useful. Be aware that if you use a container with tapered sides you cannot use a paint mixing stick, as this changes the mixing ratio as the cup gets larger towards the top. Paint sticks are only to be used in containers with straight sides. Paper cups are cautioned against because some may have a wax coating. Similarly, plastic cups or containers (medicine cups, yogurt containers, cleaned bottle caps, etc.) are also cautioned against. There are many different kinds of plastic, some of which are inappropriate for storing certain types of finishing products. | ||
*Use inexpensive plastic condiment bottles to dispense buffing compounds, polish, and glazes. | *Use inexpensive plastic condiment bottles to dispense buffing compounds, polish, and glazes. | ||
| Line 13: | Line 13: | ||
*For stirring paint, use inexpensive "jumbo sticks", tongue depressors, Popsicle sticks, wood sticks, or butter knives. | *For stirring paint, use inexpensive "jumbo sticks", tongue depressors, Popsicle sticks, wood sticks, or butter knives. | ||
*Paint stirring sticks with marks for different mix ratios can be useful for mixing paint. | *Paint stirring sticks with marks for different mix ratios can be useful for mixing paint. | ||
| − | *When mixing double portions of paint or primer | + | *When mixing double portions of paint or primer mix one portion at a time. For example, 8:2:1 is easier to keep track of than 16:4:2. After mixing each individual portion, add the two portions together and mix well again. This also cuts down on wasted material when you make a mistake (too much hardener, wrong reducer, etc.). |
*When opening a gallon of paint that isn't all going to be used immediately, mix it very well and pour it off into quart cans. While pouring, intermix the paint; pour a little bit into each can at a time. | *When opening a gallon of paint that isn't all going to be used immediately, mix it very well and pour it off into quart cans. While pouring, intermix the paint; pour a little bit into each can at a time. | ||
*Leftover paint with hardener can be placed in the refrigerator. The cold temperature will slow down the hardener. | *Leftover paint with hardener can be placed in the refrigerator. The cold temperature will slow down the hardener. | ||
| − | *It's very important to keep the nozzles of spray cans clean. Be sure to shake spray cans for the amount of time listed on the can, no less. After shaking, turn the can upside down and spray once to clear the nozzle. When done spraying, turn the can upside down, and clear the nozzle and pickup tube by spraying out all of the paint that is inside them. For more details, see Brian Martin's article posted on the Hotrodders Bulletin Board: [http://www.hotrodders.com/forum/what-proper-way-spray-paint-can-41513.html#post285843 Rattle can basics]. | + | *It's very important to keep the nozzles of spray cans clean. Be sure to shake spray cans for the amount of time listed on the can, no less. After shaking, turn the can upside down and spray once to clear the nozzle. When done spraying, turn the can upside down, and clear the nozzle and pickup tube by spraying out all of the paint that is inside them. Then wipe the nozzle clean with a suitable solvent. This will return the nozzle to nearly new condition and will greatly extend its life. For more details, see Brian Martin's article posted on the Hotrodders Bulletin Board: [http://www.hotrodders.com/forum/what-proper-way-spray-paint-can-41513.html#post285843 Rattle can basics]. |
===Spray guns and spraying technique=== | ===Spray guns and spraying technique=== | ||
| Line 33: | Line 33: | ||
====Cleaning spray guns==== | ====Cleaning spray guns==== | ||
*Never use anything metal for cleaning paint guns. | *Never use anything metal for cleaning paint guns. | ||
| − | *Rubber-tipped dental tools for cleaning | + | *Rubber-tipped dental tools for cleaning guns can be used for cleaning the holes in air caps. |
| − | *To clean metal parts of paint guns | + | *To clean metal parts of paint guns soak them in carburetor cleaner, and then rinse well. Don't soak plastic or painted parts. |
*For many spray guns from [[Harbor Freight]] (a popular spray gun supplier), the finish will be removed when the gun is soaked in thinner or carburetor cleaner for cleaning purposes. | *For many spray guns from [[Harbor Freight]] (a popular spray gun supplier), the finish will be removed when the gun is soaked in thinner or carburetor cleaner for cleaning purposes. | ||
*Try using an ultrasonic cleaner (about $30, used for cleaning jewelry) for cleaning an HVLP gun. Lacquer thinner or glass cleaner have been recommended as potential solvents for use in an ultrasonic cleaner. | *Try using an ultrasonic cleaner (about $30, used for cleaning jewelry) for cleaning an HVLP gun. Lacquer thinner or glass cleaner have been recommended as potential solvents for use in an ultrasonic cleaner. | ||
| Line 65: | Line 65: | ||
*Use proper techniques for removing old or rusted bolts. See [[Removing rusted and broken fasteners]]. | *Use proper techniques for removing old or rusted bolts. See [[Removing rusted and broken fasteners]]. | ||
*To protect painted bolts, place a sandwich bag over the bolt head before pushing on the socket. | *To protect painted bolts, place a sandwich bag over the bolt head before pushing on the socket. | ||
| + | *Make sure you save and mark all alignment shims from all the body panels when you take them apart. It will give you a great starting place when you go to reassemble. | ||
*When aligning a body part that will require a lot of loosening and tightening, use mock-up bolts with plastic washers. When the panel fit is perfect, go back and change out the bolts one by one. | *When aligning a body part that will require a lot of loosening and tightening, use mock-up bolts with plastic washers. When the panel fit is perfect, go back and change out the bolts one by one. | ||
*When disassembling parts or vehicles, be organized. Plastic bags, tape, and a magic marker are essential. | *When disassembling parts or vehicles, be organized. Plastic bags, tape, and a magic marker are essential. | ||
| Line 90: | Line 91: | ||
*Make paper templates for easy cutting and drilling. For more information and photos, see Brian Martin's article posted on the Hotrodders Bulletin Board: [http://www.hotrodders.com/forum/tip-day-13-a-71092.html Templates for accurate cutting and drilling]. | *Make paper templates for easy cutting and drilling. For more information and photos, see Brian Martin's article posted on the Hotrodders Bulletin Board: [http://www.hotrodders.com/forum/tip-day-13-a-71092.html Templates for accurate cutting and drilling]. | ||
*Before installing weld-on parts (core supports, quarter panels, rear panels, etc.), scuff the inside areas. It's easier to do this before parts are installed. | *Before installing weld-on parts (core supports, quarter panels, rear panels, etc.), scuff the inside areas. It's easier to do this before parts are installed. | ||
| − | *For doing small | + | *For doing small touch ups without ending up with a huge repair area from sanding, cut sanding discs down to size. |
*To remove creases and dents from plastic bumpers, heat them with a heat gun, and work the area while it's hot. A wallpaper seam roller can be used to work dents out from the back side of the bumper, and a window screen bead installer can be used to push creases down from the front. Flex filler can be used for finishing. | *To remove creases and dents from plastic bumpers, heat them with a heat gun, and work the area while it's hot. A wallpaper seam roller can be used to work dents out from the back side of the bumper, and a window screen bead installer can be used to push creases down from the front. Flex filler can be used for finishing. | ||
*When chemical stripping parts with heavy buildup: | *When chemical stripping parts with heavy buildup: | ||
| Line 111: | Line 112: | ||
*Oil filter shells can be used for making recessed tail lights. They come in many different sizes, and the larger ones for commercial trucks may be especially useful. | *Oil filter shells can be used for making recessed tail lights. They come in many different sizes, and the larger ones for commercial trucks may be especially useful. | ||
*To make a custom body grommet, use a section of vacuum hose that's been split down the middle with a razor or similar tool. A photo of this can be seen here: [http://hotrodders.com/gallery/showphoto.php/photo/17678/size/big/cat/500/page/ Hotrodders Photo Gallery]. | *To make a custom body grommet, use a section of vacuum hose that's been split down the middle with a razor or similar tool. A photo of this can be seen here: [http://hotrodders.com/gallery/showphoto.php/photo/17678/size/big/cat/500/page/ Hotrodders Photo Gallery]. | ||
| − | *To pull weld studs easier than the pullers can that come with the cheap weld stud guns, weld a pair of | + | *To pull weld studs easier than the pullers can that come with the cheap weld stud guns, weld a pair of vice grips to a regular dent puller. They can be tack welded to a screw-on accessory and used as a new attachment. |
==Questionable or disputed tips== | ==Questionable or disputed tips== | ||
Your Privacy Choices