Editing How to cut steel with a torch safely
Line 1: | Line 1: | ||
− | + | There are MANY things to take into consideration, before you are ready to open the bottles & strike the flame. | |
− | There are MANY things to take into consideration, before you are ready to open the bottles & strike the flame. Please read & understand all that is said here. | + | Please read & understand all that is said here. |
If there is something that is unclear in the writing or your understanding please ask your question @ www.hotrodders.com. | If there is something that is unclear in the writing or your understanding please ask your question @ www.hotrodders.com. | ||
− | + | Equipment needed: | |
Oxygen bottle | Oxygen bottle | ||
Line 32: | Line 32: | ||
Torch wrench | Torch wrench | ||
− | + | ---------------------------------------- | |
− | For the 1st example will be cutting a exhaust system off a car on a lift in a | + | |
+ | For the 1st example will be cutting a exhaust system off a car on a lift in a Professional environment .100% steel like on older cars. | ||
+ | Newer cars have a staainless compound that make it difficult to cut with a torch. | ||
+ | |||
+ | A garage with multiple employees. | ||
Move the torch cart to the work area make sure the work area is clean of debris & anything you can slip ,trip or stumble on. | Move the torch cart to the work area make sure the work area is clean of debris & anything you can slip ,trip or stumble on. | ||
− | Inspect the vehicle's fuel lines making absolutely sure you know where they are & they are in no way damaged | + | Inspect the vehicle's fuel lines making absolutely sure you know where they are & they are in no way damaged . |
− | + | If they are damaged properly repair the fuel lines before using torches. | |
− | + | Suit up from head to toes ,you should be covered. | |
+ | You also want to keep your body hydrated if you will be suited up for a long period of time. | ||
− | + | Before you put your head gear on, un roll your hoses. | |
− | + | Look around you make sure that there are no potential flammable things . | |
− | + | It is also good to let your workmates know what you are doing so they do not create a situation that would be undesirable & irreversible. | |
− | + | {example: the person in the next bay removing , dropping & spilling a fuel tank while you are cutting} | |
− | + | Open the Valves on the Bottles very slowly one @ a time . | |
− | + | ALL THE WAY . | |
+ | the valves on the bottles are designed to be all the way open or all the way off. | ||
− | Some people will say: | + | Some people will say : |
"If there is a explosion I want to be able to turn them off quick" | "If there is a explosion I want to be able to turn them off quick" | ||
− | This is a false dangerous way of thinking. If there is a explosion 99% of the time there will be no time to turn them off. | + | This is a false dangerous way of thinking. |
+ | If there is a explosion 99% of the time there will be no time to turn them off. | ||
+ | in my experience | ||
− | + | Opening them too fast can & will cause damage to the diaphragm in the regulator. | |
+ | |||
+ | The high pressure gage indicator needle should rise very slowly & then the low pressure gage indicator needle will follow. | ||
− | Completely suited up | + | Make sure you know where all fire extinguishers are located . |
+ | You should have one ready in your work area. | ||
+ | It is common to have a 2.5 gallon air over water extinguisher when cutting frequently in unpredictable areas. | ||
+ | |||
+ | Completely suited up {If you have a complete Welding Suit}if not | ||
+ | Good Boots ,good jeans, not torn or ripped ,Welding sleeves {minimum} welding gloves burning goggles & protective head wear. | ||
In some situations a respirator could be necessary. | In some situations a respirator could be necessary. | ||
− | Plan your actions, then fire up the torch | + | Plan your actions, then fire up the torch Oxy then Acetylene . |
+ | The cutting rose bud does not need to roar . | ||
+ | |||
+ | |||
+ | On the cutting torch. | ||
+ | |||
+ | Turn on just crack open the Oxy {green hose} turn on just crack open acetylene {red hose} | ||
+ | Spark the gases with the striker. | ||
+ | Mix until the flame until it is making sharp cones but not roaring. | ||
+ | |||
+ | Too much Oxy cools the metal & Makes the cutting difficult. | ||
+ | |||
+ | Bring tip up to metal slowly move the tip around to "get the heat " into the metal when the metal turns bright fire red & starts to sparkle then lever in some OXY . | ||
− | + | What you are looking to do is to blow the molten metal out of the way. | |
− | + | ||
− | + | ||
− | + | Now looking @ the pipe long ways start @ the top leaving just the very top in place & cut down wards. | |
+ | If you can move to the other side & from top to bottom cut the remaining . | ||
− | + | If you are unable to get around to the other side cut enuf pipe out of the side closest to you to allow the torch head fit inside allowing room to reach the other side of the pipe. | |
− | + | Making sure not to let the pipe cut your hose or fall on your legs or feet. | |
− | + | Be careful not to cut into anything that is not the pipe. | |
− | + | Be Very careful to watch where you aim your sparks. | |
− | + | When done cutting turn off Acetylene first the Oxy. | |
− | + | Make sure tip is cooled before rolling up the hose. | |
− | Turn off bottles | + | Turn off bottles & make sure there are no fires or hot metal when you leave the area. |
− | + | 10/7/2008 SR66 | |
− | + |