Editing Do-it-yourself Heating and Air Conditioning Replacement Guide
Jump to:
navigation
,
search
The average HVAC company charges hundreds of dollars to install a heater. One excellent way to conserve money is to install it yourself. Use this DIY furnace installation guide to help you do just that. These instructions will certainly be for changing a gas heater. You can quickly adapt the guideline for other kinds of units. Step-By-Step Furnace Installation Instructions 1. Prepare to install the unit The first step is to eliminate all loose parts from the furnace and have your installation instructions handy. 2. Pick the area of the air shaft Next choose which side of the furnace the return air duct is going to be linked to. Another choice is for it to connect to the bottom. The majority of devices have actually the cabinets marked with the appropriate size opening. You then simply need to cut the opening in the bottom or proper side. 3. Location furnace in the preferred area. To minimize noise while it is running, place the heating system on a rubber seclusion pad. If the furnace is going to be in the basement, see to it there are blocks supporting it four inches at least above the floor. If the heater installation will be in the attic, you have to take some special safety measures. Put a secondary drain pan underneath the system. 4. Choose which side the condensate drain is going to exit. When you are putting the furnace in place, ensure it is almost level yet a little sloped in the direction of the condensate drain exit. 5. Link the duct system. As soon as the heating system is in place, it is time to link the duct system. Seal the unit connections with a duct sealant or metal foil tape. 6. Link the vent pipelines. A high performance heater will have an exhaust and inlet constructed of pvc. Ensure to clean clean the pvc joints and glue them. Have the pipes slope back to the furnace at 1/4 inch for every 4 feet to permit proper condensate drain. 7. Link the supply of gas to the heater. A shutoff valve need to be installed on the outside of the heater. A drip leg needs to be set up before the line that gets in the unit. To do this use a tee that has a capped nipple that stands out of all-time low. The center part of the tee enters into the heating system and the gas supply enters the top. After the gas piping has been installed, make sure there aren't any gas leakages. To look for this, spray gas leak detector solution onto the connections. Bubbles will certainly form if there are any leaks. 8. Make electrical connections. A brand-new heating system will have line voltage (120v) and low voltage (24v) connections. Thoroughly follow the wiring directions supplied by the maker and then confirm all electrical wiring prior to turning the power on. 9. Connect condensate drain. Run a 3/4 inch pvc pipeline over to the drain area (generally this is a floor drain). 10. Start the heater and run the unit through its heating cycle. This is the last step in the heating system installation process. Check for right condensate drain and perform one more gas leakage check. Use this DIY furnace installation guide to help you do simply that. These instructions will certainly be for replacing a gas furnace. Next choose which side of the heating system the return air duct is going to be linked to. A high efficiency heating system will have an exhaust and inlet made out of pvc. The center part of the tee goes into the gas and the furnace supply comes into the top. [https://www.youtube.com/watch?v=-5W7IsNxjo8 home improvements]
|
Editing help
(opens in new window)
Personal tools
Log in / create account
Namespaces
Page
Discussion
Variants
Views
Read
Edit
View history
Actions
Search
Navigation
Main Page
Recent changes
Random page
Help
All articles
Start a new article
Hotrodders forum
Categories
Best articles
Body and exterior
Brakes
Cooling
Electrical
Engine
Fasteners
Frame
Garage and shop
General hotrodding
Identification and decoding
Interior
Rearend
Safety
Steering
Suspension
Tires
Tools
Transmission
Troubleshooting
Wheels
Toolbox
What links here
Related changes
Special pages
Terms of Use
Copyright
Privacy Policy
Your Privacy Choices
Manage Consent