Rearend identification

From Crankshaft Coalition Wiki
Jump to: navigation, search
(→GM RPO axle codes)
 
Line 1: Line 1:
−
{{develop1}}<br>
+
 
 
==Introduction==
 
==Introduction==
 
There are several ways to tell what the type/size/application of a rearend. Besides visually checking and comparing rearends to one another, there are casting numbers, build codes and dates displayed or cast/stamped in various locations on the rearend and elsewhere. These all can be used to help ID a rearend.
 
There are several ways to tell what the type/size/application of a rearend. Besides visually checking and comparing rearends to one another, there are casting numbers, build codes and dates displayed or cast/stamped in various locations on the rearend and elsewhere. These all can be used to help ID a rearend.
Line 5: Line 5:
 
==Casting numbers==
 
==Casting numbers==
 
Many if not all rear end housings will have some sort of casting number or ID cues to identify it. If the RPO decal is present (newer vehicles) or the broadcast or "build" sheet is available, it can show what was originally in the vehicle. Sometimes body/fender/cowl tags contain coded info that may list specifics on the rearend.
 
Many if not all rear end housings will have some sort of casting number or ID cues to identify it. If the RPO decal is present (newer vehicles) or the broadcast or "build" sheet is available, it can show what was originally in the vehicle. Sometimes body/fender/cowl tags contain coded info that may list specifics on the rearend.
 +
  
 
==Axle codes==
 
==Axle codes==
Line 14: Line 15:
 
*[http://www.thecamaro.com/Decoding/Chevy-Axle-Rear-End-Decoding/ Chevrolet Rear Axle Code Identification and Decoding] from thecamaro.com  
 
*[http://www.thecamaro.com/Decoding/Chevy-Axle-Rear-End-Decoding/ Chevrolet Rear Axle Code Identification and Decoding] from thecamaro.com  
 
*[http://www.thecamaro.com/Decoding/Chevy-Axle-Rear-End-Decoding/Chevy-Full-Size-Rear-Axle-Codes.php Chevrolet Full Size and Impala Rear End/Axle Assembly Codes] from from thecamaro.com
 
*[http://www.thecamaro.com/Decoding/Chevy-Axle-Rear-End-Decoding/Chevy-Full-Size-Rear-Axle-Codes.php Chevrolet Full Size and Impala Rear End/Axle Assembly Codes] from from thecamaro.com
−
*[http://aplsweb.com/Topics/Differential.htm Various tid-bits, et cetera] from aplsweb.com
 
 
*[http://tech.oldsgmail.com/axle_useage.php GM A-body codes] from tech.oldsgmail.com
 
*[http://tech.oldsgmail.com/axle_useage.php GM A-body codes] from tech.oldsgmail.com
 
*[http://www.gnttype.org/numbers/axcodes.html Gear ratio info] from gnttype.org
 
*[http://www.gnttype.org/numbers/axcodes.html Gear ratio info] from gnttype.org
Line 106: Line 106:
  
 
===Columbia 2-speed rear end===
 
===Columbia 2-speed rear end===
−
More of an overdrive unit than an actual rear end. Included in the Ford section since it was offered as an option on '30's to '40's Fords.
+
More of an overdrive unit than an actual rear end. Included in the Ford section since it was offered as an option on '30s to '40s Fords.
  
 
==General Motors==
 
==General Motors==
Line 145: Line 145:
  
 
====8.5 inch 10-bolt====
 
====8.5 inch 10-bolt====
−
Sometimes referred to as the "corporate 10-bolt", the GM 8.5" 10-bolt rearend began production in 1971 to replace the 8.2" and 12-bolt rearends. There was simultaneous use of the 8.2" and 8.5" rearends during the changeover period, like in the Nova. Has a 10 bolt cover as well as 10 bolts securing the ring gear.
+
Sometimes referred to as the "corporate 10-bolt", the GM 8.5" 10-bolt rearend began production in 1971 to replace the 8.2" and 12-bolt rearends. There was simultaneous use of the 8.2" and 8.5" rearends during the changeover period, like in the Nova. Has a 10 bolt cover as well as 10 bolts securing the ring gear. Ring gear bolts are 7/16 - 20 LH threads (also shared with the 7.5/7.625").  
  
−
The 8.5" 10-bolt GM rearend has a 30 spline pinion, uses C-clips, and could have 28 or 30 spline axles depending on the year. It uses a 1-1/4" pinion nut.
+
The 8.5" 10-bolt GM rearend has a 30 spline pinion, uses C-clips, and could have 28 or 30 spline axles depending on the year (30 spline axles were used after 1988). 4 wheel drive 8.5" front differentials manufactured between 1977-91 share the same differential gears, bearings, and pinion seals but has a modified housing and cover which has an indentation to clear suspension travel. It uses a 1-1/4" pinion nut. Ring gear diameter was increased to 8.6" when used with the GMT800 platform light duty trucks (1999-06 Silverado/Sierra).  
 
<table  bgcolor="#F9F9F9" table border="1" cellpadding="2" cellspacing="0"><tr> <td>                                Apollo:&nbsp;&nbsp;1973 - 1975&nbsp;&nbsp;
 
<table  bgcolor="#F9F9F9" table border="1" cellpadding="2" cellspacing="0"><tr> <td>                                Apollo:&nbsp;&nbsp;1973 - 1975&nbsp;&nbsp;
 
                                 </td><td>                                    Bel Air:&nbsp;&nbsp;1970 - 1975&nbsp;&nbsp;
 
                                 </td><td>                                    Bel Air:&nbsp;&nbsp;1970 - 1975&nbsp;&nbsp;
Line 157: Line 157:
 
</tr><tr>
 
</tr><tr>
 
<td>                                    C10 1/2 Ton (2WD):&nbsp;&nbsp;1979 - 1987&nbsp;&nbsp;
 
<td>                                    C10 1/2 Ton (2WD):&nbsp;&nbsp;1979 - 1987&nbsp;&nbsp;
−
                                 </td><td>                                    C15/ C1500 1/2 Ton (2WD):&nbsp;&nbsp;1979 - 1990&nbsp;&nbsp;
+
                                 </td><td>                                    C15/ C1500 1/2 Ton (2WD):&nbsp;&nbsp;1979 - present&nbsp;&nbsp;
 
                                 </td>
 
                                 </td>
 
</tr><tr>
 
</tr><tr>
−
<td>                                    C1500 1/2 Ton (2WD):&nbsp;&nbsp;1988 - 1990&nbsp;&nbsp;
+
<td>                                    C1500 1/2 Ton (2WD):&nbsp;&nbsp;1988 - 1998 (incl. GMT400-based Blazer (92-94), Tahoe/Yukon, Escalade, Denali, 1/2 ton Suburban)&nbsp;&nbsp;
 
                                 </td><td>                                    Camaro:&nbsp;&nbsp;1970 - 1981&nbsp;&nbsp;
 
                                 </td><td>                                    Camaro:&nbsp;&nbsp;1970 - 1981&nbsp;&nbsp;
 
                                 </td>
 
                                 </td>
 
</tr><tr>
 
</tr><tr>
−
<td>                                    Caprice:&nbsp;&nbsp;1970 - 1996&nbsp;&nbsp;
+
<td>                                    Caprice:&nbsp;&nbsp;1970 - 1996 (includes '94-'96 Impala SS and 9C1 police package)&nbsp;&nbsp;
 
                                 </td><td>                                    Catalina:&nbsp;&nbsp;1970 - 1981&nbsp;&nbsp;
 
                                 </td><td>                                    Catalina:&nbsp;&nbsp;1970 - 1981&nbsp;&nbsp;
 
                                 </td>
 
                                 </td>
 
</tr><tr>
 
</tr><tr>
 
<td>                                    Chevelle/Malibu:&nbsp;&nbsp;1973 - 1973&nbsp;&nbsp;
 
<td>                                    Chevelle/Malibu:&nbsp;&nbsp;1973 - 1973&nbsp;&nbsp;
−
                                 </td><td>                                    Cutlas:&nbsp;&nbsp;1970 - 1977&nbsp;&nbsp;
+
                                 </td><td>                                    Cutlass:&nbsp;&nbsp;1970 - 1977&nbsp;&nbsp;
 
                                 </td>
 
                                 </td>
 
</tr><tr>
 
</tr><tr>
−
<td>                                    Cutlas:&nbsp;&nbsp;1985 - 1987&nbsp;&nbsp;
+
<td>                                    Cutlass:&nbsp;&nbsp;1985 - 1987 (442 package)&nbsp;&nbsp;
 
                                 </td><td>                                    El Camino:&nbsp;&nbsp;1971 - 1976&nbsp;&nbsp;
 
                                 </td><td>                                    El Camino:&nbsp;&nbsp;1971 - 1976&nbsp;&nbsp;
 
                                 </td>
 
                                 </td>
Line 192: Line 192:
 
                                 </td>
 
                                 </td>
 
</tr><tr>
 
</tr><tr>
−
<td>                                    Impala:&nbsp;&nbsp;1971 - 1988&nbsp;&nbsp;
+
<td>                                    Impala/Caprice:&nbsp;&nbsp;1971 - 1996 ('77-'96 B, C, and D platform for station wagons, diesels, 9C6 (taxicab) and 9C1 police package&nbsp;&nbsp;
−
                                 </td><td>                                    K10/ K1500 1/2 Ton (4WD):&nbsp;&nbsp;1979 - 1988&nbsp;&nbsp;
+
                                 </td><td>                                    K10/ K1500 1/2 Ton (4WD):&nbsp;&nbsp;1979 - present&nbsp;&nbsp;
 
                                 </td>
 
                                 </td>
 
</tr><tr>
 
</tr><tr>
−
<td>                                    K15/ K1500 1/2 Ton (4WD):&nbsp;&nbsp;1979 - 1988&nbsp;&nbsp;
+
<td>                                    K15/ K1500 1/2 Ton (4WD):&nbsp;&nbsp;1979 - present&nbsp;&nbsp;
−
                                 </td><td>                                    K5 Blazer (4WD):&nbsp;&nbsp;1979 - 1991&nbsp;&nbsp;
+
                                 </td><td>                                    K5 Blazer (4WD):&nbsp;&nbsp;1979 - 1991 (1979-'82 are overlap years - also applicable to C/K 10 series incl. Suburban&nbsp;&nbsp;
 
                                 </td>
 
                                 </td>
 
</tr><tr>
 
</tr><tr>
Line 219: Line 219:
 
                                 </td><td>                                    Skylark:&nbsp;&nbsp;1970 - 1972&nbsp;&nbsp;
 
                                 </td><td>                                    Skylark:&nbsp;&nbsp;1970 - 1972&nbsp;&nbsp;
 
                                 </td>
 
                                 </td>
−
</tr><tr>
+
                </tr><tr>
 
<td>                                    Skylark:&nbsp;&nbsp;1975 - 1979&nbsp;&nbsp;
 
<td>                                    Skylark:&nbsp;&nbsp;1975 - 1979&nbsp;&nbsp;
−
                                 </td><td>                                    Sonoma:&nbsp;&nbsp;1994 - 1998&nbsp;&nbsp;
+
                                 </td><td>                                    S10,Sonoma:&nbsp;&nbsp;1995 - 2003 (4WD with ZR2 option, S10 SS, Xtreme, and 4.3L trucks with a manual transmission option&nbsp;&nbsp;
 
                                 </td>
 
                                 </td>
 
</tr><tr>
 
</tr><tr>
Line 283: Line 283:
  
 
==8.5" non C-clip rearend==
 
==8.5" non C-clip rearend==
 +
The non C-clip differential share the same ring/pinion (incl. pinion bearings, differential carrier) with the C clip version but has pressed on axle bearings similar to a Dana 44 or Ford 9 inch. Differential cover looks similar to the BOP 8.2 10 bolt.
 +
 
The 1971-'72 Buick GS/Skylark and Olds Cutlass A-body 8.5 10 bolt did not have C-clip axles.  
 
The 1971-'72 Buick GS/Skylark and Olds Cutlass A-body 8.5 10 bolt did not have C-clip axles.  
  
 
The non C-clip 8.5" 10 bolt, type "C" rearend was used in some 1969-'72 Pontiac GP and 1970-'72 Monte Carlo.  
 
The non C-clip 8.5" 10 bolt, type "C" rearend was used in some 1969-'72 Pontiac GP and 1970-'72 Monte Carlo.  
  
−
There have been non C-clip rearends found in Chevelle wagons through at least 1974.  
+
There have been non C-clip rearends found in Chevelle wagons, and some El Caminos through at least 1974.
  
 
==12-bolt cover/10-bolt ring gear==
 
==12-bolt cover/10-bolt ring gear==
Line 336: Line 338:
  
 
==U-joints==
 
==U-joints==
−
*1310 series, (aka "small Chevy") has 1.063" diameter caps, 3.219" measured across to lock ring points (1-1/16" x 3-7/32"), uses outside clips. Was OEM for many 1967-74 GM cars.<br>  
+
*1310 series, (aka "small Chevy") has 1.063" diameter caps, 3.219" measured across to lock ring points (1-1/16" x 3-7/32"), uses outside clips. Was OEM for many 1967-74 GM cars. Also used with Ford F100s (including early F150s prior to 1980), Broncos, Econolines with 9 inch differentials and AMC/Jeep products (pinion to driveshaft location - driveshaft to transmission yoke used a hybrid U-joint with outside and inside clips)<br>  
−
{{Note1}}There's also a 1310 "special" U-joint, which has two 1-1/16" and two 1-1/8" caps. Used OE on some Fords and used as an adapter U-joint.
+
{{Note1}}There's also a 1310 "special" U-joint, which has two 1-1/16" and two 1-1/8" caps. Used OE on some Fords and available from the aftermarket as an adapter U-joint.
 
*1330 series pinion yokes use locating tabs to center the U-joint, has 1.063" diameter caps, 3.625" measured across to lock ring points (1-1/16" x 3-5/8"), uses outside clips. Used on heavy-duty/high performance/big engine applications.
 
*1330 series pinion yokes use locating tabs to center the U-joint, has 1.063" diameter caps, 3.625" measured across to lock ring points (1-1/16" x 3-5/8"), uses outside clips. Used on heavy-duty/high performance/big engine applications.
 
*GM 3R series is the "inside C-clip", or "inside lock" style. Used ~1975-up. It does not use locating tabs. It has 1.125" diameter caps, 2.5625" measured across caps (1-1/8" x 2-9/16"), aftermarket/replacement U-joints uses inside clips, originals use plastic injection.
 
*GM 3R series is the "inside C-clip", or "inside lock" style. Used ~1975-up. It does not use locating tabs. It has 1.125" diameter caps, 2.5625" measured across caps (1-1/8" x 2-9/16"), aftermarket/replacement U-joints uses inside clips, originals use plastic injection.
Line 375: Line 377:
  
 
===15 series rearend===
 
===15 series rearend===
−
The AMC 15 series rearend has a 7-9/16" ring gear. It was used in 1965 and earlier models with 196 ci or 199 ci inline 6 engines. The small cars (cars other than those listed below as "big car") used the AMC 15 rearend with inline 6 engines, AMC 20 rearend was used with V8 engines. The AMC 20 rearend could be ordered in fleet cars with inline 6 engines.
+
The AMC 15 series rearend has a 7-9/16" ring gear. It was used in 1965 and earlier models with 196 ci or 199 ci inline 6 engines. The small cars (cars other than those listed below as "big car") used the AMC 15 rearend with inline 6 engines, AMC 20 rearend was used with V8 engines. The AMC 20 rearend could be ordered in fleet cars with inline 6 engines. AMC sold the tooling equipment for its differentials to the Dana Corporation in 1985. The AMC 15 was modified by Dana and rebranded as the Dana 35/35C. Ring/pinion sets including the axleshafts do not interchange with the AMC 15.
  
 
===20 series rearend===
 
===20 series rearend===
 
The big cars (Ambassador, Classic, Rebel, Matador and Marlin) used the AMC 20 rearend with 232 ci inline 6 and bigger engines.
 
The big cars (Ambassador, Classic, Rebel, Matador and Marlin) used the AMC 20 rearend with 232 ci inline 6 and bigger engines.
  
−
The series 20 was used in Jeeps as well as AMC passenger cars.  A Jeep 20 series rearend would have a 5 on 5" bolt pattern. Passenger cars used the 5 on 4-1/2" wheel bolt pattern.
+
The series 20 was used in Jeeps as well as AMC passenger cars.  A Jeep 20 series rearend would have a 5 on 5" wheel bolt pattern. Passenger cars used the 5 on 4-1/2" wheel bolt pattern.
  
 
[[File:Amc 20 series rearend.jpg|thumb|450px|left|20 series under a 1966 Rouge]] <br style="clear:both"/>  
 
[[File:Amc 20 series rearend.jpg|thumb|450px|left|20 series under a 1966 Rouge]] <br style="clear:both"/>  
Line 462: Line 464:
 
<div align="center">
 
<div align="center">
 
3.08
 
3.08
−
</div>
 
−
</td>
 
−
</tr>
 
−
<tr height="13">
 
−
<td>G92</td>
 
−
<td colspan="3" height="13"> Performance  </td>
 
−
<td>
 
−
<div align="center">
 
 
</div>
 
</div>
 
</td>
 
</td>
Line 538: Line 532:
 
<tr height="13">
 
<tr height="13">
 
<td>GH7</td>
 
<td>GH7</td>
−
<td colspan="3" height="13"> Axle  Rear</td>
+
<td colspan="3" height="13">Axle  Rear</td>
 
<td>
 
<td>
 
<div align="center">
 
<div align="center">
Line 547: Line 541:
 
<tr height="13">
 
<tr height="13">
 
<td>GJ1</td>
 
<td>GJ1</td>
−
<td colspan="3" height="13"> Axle  Rear</td>
+
<td colspan="3" height="13">Axle  Rear</td>
 
<td>
 
<td>
 
<div align="center">
 
<div align="center">
Line 556: Line 550:
 
<tr height="13">
 
<tr height="13">
 
<td>GJ2</td>
 
<td>GJ2</td>
−
<td colspan="3" height="13"> Axle  Rear</td>
+
<td colspan="3" height="13">Axle  Rear</td>
 
<td>
 
<td>
 
<div align="center">
 
<div align="center">
Line 565: Line 559:
 
<tr height="13">
 
<tr height="13">
 
<td>GK7</td>
 
<td>GK7</td>
−
<td colspan="3" height="13"> Axle  Rear</td>
+
<td colspan="3" height="13">Axle  Rear</td>
 
<td>
 
<td>
 
<div align="center">
 
<div align="center">
Line 574: Line 568:
 
<tr height="13">
 
<tr height="13">
 
<td>GK8</td>
 
<td>GK8</td>
−
<td colspan="3" height="13"> Axle  Rear</td>
+
<td colspan="3" height="13">Axle  Rear</td>
 
<td>
 
<td>
 
<div align="center">
 
<div align="center">
Line 592: Line 586:
 
<tr height="13">
 
<tr height="13">
 
<td>GL0</td>
 
<td>GL0</td>
−
<td colspan="3" height="13"> Axle  Rear</td>
+
<td colspan="3" height="13">Axle  Rear</td>
 
<td>
 
<td>
 
<div align="center">
 
<div align="center">
Line 619: Line 613:
 
<tr height="13">
 
<tr height="13">
 
<td>GM2</td>
 
<td>GM2</td>
−
<td colspan="3" height="13"> Axle  Rear</td>
+
<td colspan="3" height="13">Axle  Rear</td>
 
<td>
 
<td>
 
<div align="center">
 
<div align="center">
Line 637: Line 631:
 
<tr height="13">
 
<tr height="13">
 
<td>GM4</td>
 
<td>GM4</td>
−
<td colspan="3" height="13"> Axle  Rear</td>
+
<td colspan="3" height="13">Axle  Rear</td>
 
<td>
 
<td>
 
<div align="center">
 
<div align="center">
Line 646: Line 640:
 
<tr height="13">
 
<tr height="13">
 
<td>GM5</td>
 
<td>GM5</td>
−
<td colspan="3" height="13"> Axle  Rear</td>
+
<td colspan="3" height="13">Axle  Rear</td>
 
<td>
 
<td>
 
<div align="center">
 
<div align="center">
Line 655: Line 649:
 
<tr height="13">
 
<tr height="13">
 
<td>GM6</td>
 
<td>GM6</td>
−
<td colspan="3" height="13"> Axle  Rear</td>
+
<td colspan="3" height="13">Axle  Rear</td>
 
<td>
 
<td>
 
<div align="center">
 
<div align="center">
Line 664: Line 658:
 
<tr height="13">
 
<tr height="13">
 
<td>GM7</td>
 
<td>GM7</td>
−
<td colspan="3" height="13"> Axle  Rear</td>
+
<td colspan="3" height="13">Axle  Rear</td>
 
<td>
 
<td>
 
<div align="center">
 
<div align="center">
Line 735: Line 729:
 
<tr height="13">
 
<tr height="13">
 
<td>GS8</td>
 
<td>GS8</td>
−
<td colspan="3" height="13"> Axle  Rear</td>
+
<td colspan="3" height="13">Axle  Rear</td>
 
<td>
 
<td>
 
<div align="center">
 
<div align="center">
Line 759: Line 753:
 
</div>
 
</div>
 
</td>
 
</td>
−
</tr></table></font> </div>
+
</tr>
−
<div><font size="1"><table style="float: center;" border="1" cellpadding="2" cellspacing="0">
+
 
<tr height="13">
 
<tr height="13">
 
<td>GT4</td>
 
<td>GT4</td>
Line 769: Line 762:
 
</div>
 
</div>
 
</td>
 
</td>
−
</tr>
+
</tr></table></font> </div>
 +
<div><font size="1"><table style="float: center;" border="1" cellpadding="2" cellspacing="0">
 
<tr height="13">
 
<tr height="13">
 
<td>GT5</td>
 
<td>GT5</td>
Line 853: Line 847:
 
<tr height="13">
 
<tr height="13">
 
<td>GU7</td>
 
<td>GU7</td>
−
<td colspan="3" height="13"> Axle  Rear</td>
+
<td colspan="3" height="13">Axle  Rear</td>
 
<td>
 
<td>
 
<div align="center">
 
<div align="center">
Line 861: Line 855:
 
</tr>
 
</tr>
 
<tr height="13">
 
<tr height="13">
−
<td>GU8</td>
+
<td>GU8</td> <td colspan="3" height="13">Axle  Rear</td>
−
<td colspan="3" height="13"> Axle  Rear</td>
+
 
<td>
 
<td>
 
<div align="center">
 
<div align="center">
Line 871: Line 864:
 
<tr height="13">
 
<tr height="13">
 
<td>GU9</td>
 
<td>GU9</td>
−
<td colspan="3" height="13"> Axle  Rear</td>
+
<td colspan="3" height="13">Axle  Rear</td>
 
<td>
 
<td>
 
<div align="center">
 
<div align="center">
Line 880: Line 873:
 
<tr height="13">
 
<tr height="13">
 
<td>GV0</td>
 
<td>GV0</td>
−
<td colspan="3" height="13"> Axle  Rear</td>
+
<td colspan="3" height="13">Axle  Rear</td>
 
<td>
 
<td>
 
<div align="center">
 
<div align="center">
Line 952: Line 945:
 
<tr height="13">
 
<tr height="13">
 
<td>GV9</td>
 
<td>GV9</td>
−
<td colspan="3" height="13"> Axle  Rear</td>
+
<td colspan="3" height="13">Axle  Rear</td>
 
<td>
 
<td>
 
<div align="center">
 
<div align="center">
Line 1,051: Line 1,044:
 
<tr height="13">
 
<tr height="13">
 
<td>GX4</td>
 
<td>GX4</td>
−
<td colspan="3" height="13"> Axle  Rear</td>
+
<td colspan="3" height="13">Axle  Rear</td>
 
<td>
 
<td>
 
<div align="center">
 
<div align="center">
Line 1,060: Line 1,053:
 
<tr height="13">
 
<tr height="13">
 
<td>GX5</td>
 
<td>GX5</td>
−
<td colspan="3" height="13"> Axle  Rear</td>
+
<td colspan="3" height="13">Axle  Rear</td>
 
<td>
 
<td>
 
<div align="center">
 
<div align="center">
Line 1,069: Line 1,062:
 
<tr height="13">
 
<tr height="13">
 
<td>GX6</td>
 
<td>GX6</td>
−
<td colspan="3" height="13"> Axle  Rear</td>
+
<td colspan="3" height="13">Axle  Rear</td>
 
<td>
 
<td>
 
<div align="center">
 
<div align="center">
Line 1,078: Line 1,071:
 
<tr height="13">
 
<tr height="13">
 
<td>GX8</td>
 
<td>GX8</td>
−
<td colspan="3" height="13"> TransAxle  Final Drive </td>
+
<td colspan="3" height="13">TransAxle  Final Drive </td>
 
<td>
 
<td>
 
<div align="center">
 
<div align="center">
Line 1,096: Line 1,089:
 
<tr height="13">
 
<tr height="13">
 
<td>GY3</td>
 
<td>GY3</td>
−
<td colspan="3" height="26"> TransAxle  Final Drive</td>
+
<td colspan="3" height="26">TransAxle  Final Drive</td>
 
<td>
 
<td>
 
<p align="center">
 
<p align="center">
Line 1,105: Line 1,098:
 
<tr height="13">
 
<tr height="13">
 
<td>GY4</td>
 
<td>GY4</td>
−
<td colspan="3" height="13"> Axle  Rear</td>
+
<td colspan="3" height="13">Axle  Rear</td>
 
<td>
 
<td>
 
<div align="center">
 
<div align="center">
Line 1,114: Line 1,107:
 
<tr height="13">
 
<tr height="13">
 
<td>GY5</td>
 
<td>GY5</td>
−
<td colspan="3" height="13"> Axle  Front</td>
+
<td colspan="3" height="13">Axle  Front</td>
 
<td>
 
<td>
 
<div align="center">
 
<div align="center">
Line 1,123: Line 1,116:
 
<tr height="13">
 
<tr height="13">
 
<td>GY7</td>
 
<td>GY7</td>
−
<td colspan="3" height="13"> TransAxle  Final Drive</td>
+
<td colspan="3" height="13">TransAxle  Final Drive</td>
 
<td>
 
<td>
 
<div align="center">
 
<div align="center">
Line 1,132: Line 1,125:
 
<tr height="13">
 
<tr height="13">
 
<td>GY9</td>
 
<td>GY9</td>
−
<td colspan="3" height="13"> Axle  Rear</td>
+
<td colspan="3" height="13">Axle  Rear</td>
 
<td>
 
<td>
 
<div align="center">
 
<div align="center">

Latest revision as of 09:49, 27 March 2023

Retrieved from "https://www.crankshaftcoalition.com/wiki/index.php?title=Rearend_identification&oldid=3477211"
Personal tools
Namespaces
Variants
Actions
Navigation
Categories
Toolbox
 
Terms of Use
Copyright
Privacy Policy