Crankshaft Coalition Wiki
(→Articles to work on) |
(→Articles to work on) |
||
| Line 77: | Line 77: | ||
==Articles to work on== | ==Articles to work on== | ||
These articles are off to a good start, but still need considerable work. Specifically, they could use more information, photos, and general cleanup and organizing. | These articles are off to a good start, but still need considerable work. Specifically, they could use more information, photos, and general cleanup and organizing. | ||
| + | *[[Automobile Body and Frame Rotisserie]] | ||
| + | *[[Basic stuff for newbies]] | ||
| + | *[[Bulletproof cooling system]] | ||
| + | *[[Buffing your newly-finished paint]] | ||
| + | *[[Cadillac engine Knowledge]] | ||
| + | *[[C-clip eliminator for 8.8 Ford]] | ||
| + | *[[Cheapo paint job]] | ||
| + | *[[Cold air intakes]] | ||
*[[Cylinder Head Choice]] | *[[Cylinder Head Choice]] | ||
| + | *[[Early Hemi engine specifications]] | ||
*[[Electric Fuel Pump Mount]] | *[[Electric Fuel Pump Mount]] | ||
| + | *[[Epoxy primer]] | ||
| + | *[[First paint job]] | ||
*[[Ford 144-250 inline 6 High performance building]] | *[[Ford 144-250 inline 6 High performance building]] | ||
| + | *[[General Motors build codes]] | ||
*[[Head gasket]] | *[[Head gasket]] | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
*[[Header design]] | *[[Header design]] | ||
| + | *[[Health and Safety in the Shop or Garage]] | ||
*[[Homologation]] | *[[Homologation]] | ||
| + | *[[Hot rodding the HEI distributor]] | ||
*[[How do turn signals work?]] | *[[How do turn signals work?]] | ||
| + | *[[How to document your project]] | ||
| + | *[[How to Find Vacuum Leaks]] | ||
*[[How to find your next project]] | *[[How to find your next project]] | ||
| − | *[[How to install Mustang II IFS | + | *[[How to identify a Ford V8]] |
| + | *[[How to install Mustang II IFS Spindles]] | ||
| + | *[[How to rebuild an engine]] | ||
*[[How to rebuild automotive carburetors]] | *[[How to rebuild automotive carburetors]] | ||
| + | *[[How to remove a starter]] | ||
*[[How to solder electrical connections]] | *[[How to solder electrical connections]] | ||
| + | *[[How to title a hot rod]] | ||
*[[How to torque a bolt]] | *[[How to torque a bolt]] | ||
*[[Idle air control valve overview]] | *[[Idle air control valve overview]] | ||
| − | *[[ | + | *[[Long term storage preparation]] |
*[[More GM RPO codes]] | *[[More GM RPO codes]] | ||
*[[Pitted rust]] | *[[Pitted rust]] | ||
| − | *[[ | + | *[[Pre-1980 VIN decoding]] |
| − | *[[ | + | *[[Rearend removal]] |
| − | + | ||
| − | + | ||
| − | + | ||
*[[Rebuild an Alternator]] | *[[Rebuild an Alternator]] | ||
*[[Removal Of GM Door Panel]] | *[[Removal Of GM Door Panel]] | ||
*[[Rewiring a vehicle]] | *[[Rewiring a vehicle]] | ||
| − | *[[ | + | *[[Rebuilding an early Hemi engine]] |
| + | *[[Rust]] | ||
| + | *[[Swap Solutions: Driveshafts]] | ||
| + | *[[Swap Solutions: Engines]] | ||
| + | *[[Swap Solutions: Rear Axles]] | ||
| + | *[[Swapping to rack and pinion steering]] | ||
*[[The FREE T Bucket plans]] | *[[The FREE T Bucket plans]] | ||
| − | *[[ | + | *[[Transmission Identification]] |
*[[Suspension]] | *[[Suspension]] | ||
| − | |||
*[[Why a shorter rear gear will accelerate the car quicker]] | *[[Why a shorter rear gear will accelerate the car quicker]] | ||
| − | *[[ | + | *[[Window removal and installation]] |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
==Start a new article== | ==Start a new article== | ||
Your Privacy Choices