Editing Ring gear and pinion set up
Jump to:
navigation
,
search
{{Template:Newarticle1}} ==Overview== Setting up a differential correctly when changing the ring gear and pinion is often thought of as being a difficult task. Because of the perceived difficulty, this is something that is often farmed out. The truth is, provided there is access to the tools needed, there is no reason the average wrench cannot successfully do this job themselves. Of course you need to have guidance, patience, and the desire to see the job through, as well. ==Manuals and guides== In the case of the GM 10-bolt and 12-bolt differentials, the factory overhaul manual has a very good section dealing with setting up the rear end after a ring gear and pinion swap. The only thing about using the manual is in some cases it calls for specific GM tools- tools that may not be available to the average do-it-yourselfer. Not to worry, though. Nothing that the manual calls for cannot be duplicated or substituted, using other tools or methods. ==Tools== From article at pirate4x4.com: You will require a good, complete set of regular hand tools including the usual hammers, punches, wrenches, sockets, screwdrivers, and the like. Air tools are not a must, but will certainly make the job a lot faster and easier. You will also need the following: *Foot-pound torque wrench - you need one capable of reading at least 250 ft-lbs for torquing the pinion nut, which affects pinion-bearing preload. You can try to do without, and use a “calibrated-by-feel” cheater bar or impact wrench but you will seriously compromise your set-up if you do. *Inch-pound torque wrench – needed for reading pinion-bearing preload. “Experts” sometimes claim to be able to set this by feel. Those with a great deal of experience or a gifted touch probably can - but it's not a recommended approach for most. I certainly can’t and wouldn’t want to make do without this tool – again, it directly impacts one of the four major settings you’re trying to get right. Because you need to use the tool to measure torque while rotating the pinion, a “click-style” torque wrench will not work – you must use a beam-style or better yet a dial indicating torque wrench. Figure 7 shows the Armstrong quarter-inch drive, 0-75 in-lb model I talked myself into, despite its near $300 cost. I understand that beam-style wrenches can be purchased for much less at bicycle shops. *Dial Indicator – needed to measure run-out, backlash, and carrier shim stacks. It might be possible to get backlash close simply by reading the contact pattern, but with specs in the range of four to ten thousandths of an inch, you’re going to get a pretty rough job without a dial indicator. *0-1” micrometer calipers – needed for measuring both old and new shims. You simply cannot do the job without this one. *Set-up bearings – needed to avoid damaging real bearings and/or going insane while pulling and pressing the bearings on and off the dozen or more times you’re likely to need to while making adjustments to shim stacks. Take my advice – don’t even think about doing the job without set-up bearings. Besides, you can easily make your own set-up bearings from the old bearings – which also gives you all the reason you need to use new bearings when setting up gears – something I recommend anyway. *Gear marking compound and brush – for reading the gear tooth contact pattern, the most critical part of the entire job – you simply can’t do without it. *Bearing pullers and/or bearing separators with a press. Depending on their size, you will need one or both of these to remove the old bearing cones from the pinion and carrier. I have seen folks attempt the work with hammer and punch (ahem, cough) and the results are predictably disastrous. Don’t ask why I have a large pile of ruined bearings in the corner please! *Bearing / seal drivers and/or press – appropriate drivers are required to install the carrier-bearing cones on the carrier (a press is much preferred, but it can be done carefully with hammer and driver), the pinion cups in the housing (a driver must be used), and the bearing cones on the pinion (press preferred for inner pinion-bearing cone, driver must be used for outer). You can often fabricate your own drivers, or at least the shafts, from scrap pipe or tube; but the face should be soft (aluminum or brass) to avoid damaging the new bearings. *Pinion-nut socket – a 15/16” socket is required for the Dana 60 pinion nut, with a sufficiently thin wall to fit in the yoke. *Pry bars – required for removing the carrier from the housing in most cases. A case spreader would be better still, but is not essential. *Dead-blow hammer – needed for seating the carrier and/or pinion in the housing, especially if a case spreader is not used. A dead-blow hammer is like a combination of a mallet and a hammer: heavy like a hammer, soft-faced like a mallet to avoid damaging components. It also has a moving weight inside to reduce “bounce-back” when a blow is struck (hence the name “dead blow”). *Punch or stamp – for marking carrier-bearing caps so that they can be reinstalled correctly. *Oil drain pan, silicone RTV, thread-locker, vice, hammers, parts cleaner, rags, and a 3-foot breaker bar or large impact wrench. ==Resources== *[http://www.pirate4x4.com/articles/tech/billavista/Gear_Setup Ring gear and pinion set up] from pirate4x4.com [[Category:Rearend]] [[Category:Undeveloped articles]] [[Category:Undeveloped Rearend articles]]
|
Editing help
(opens in new window)
Template:Newarticle1
(
edit
)
Template:Rounded
(
edit
)
Personal tools
Log in / create account
Namespaces
Page
Discussion
Variants
Views
Read
Edit
View history
Actions
Search
Navigation
Main Page
Recent changes
Random page
Help
All articles
Start a new article
Hotrodders forum
Categories
Best articles
Body and exterior
Brakes
Cooling
Electrical
Engine
Fasteners
Frame
Garage and shop
General hotrodding
Identification and decoding
Interior
Rearend
Safety
Steering
Suspension
Tires
Tools
Transmission
Troubleshooting
Wheels
Toolbox
What links here
Related changes
Special pages
Terms of Use
Copyright
Privacy Policy
Your Privacy Choices
Manage Consent