Editing Lifters (section)
Jump to:
navigation
,
search
==Repairing or replacing lifters== [[File:Lifter clips 002.jpg|thumb|350px|Three styles of lifter retainers. The [http://www.truarc.com/pdfs/Truarc%20Catalog.pdf internal C-clip type] is stronger and should be used especially with solid lifters or when "zero lashing" lifters.]] {{Caution}}Lifters and cam lobes become wedded as soon as the engine fires up and the cam is broken in. From that point forward, the same lifter '''has''' to be kept on the same lobe, preferably in the same engine. To replace a faulty lifter with a new lifter (or to replace a used cam with a new cam, reusing the same lifters) is to risk cam and lifter failure requiring the engine to be torn down to remove the shrapnel left from the destruction of the cam lobe(s) and lifter(s). This will certainly cost more than what a new set of lifters and a cam would have cost from the beginning, considering that a new cam and lifters will be needed, along with gaskets, fluids and filters, down time, aggravation, etc. If the cam lobes and lifter bottoms are not excessively worn, before replacing a stuck or noisy lifter with a new lifter (which should be considered only in an emergency situation), or replacing the cam and lifters with new parts, disassemble, clean and inspect the lifter that is in question- there might be hope for it after all. ===Disassembling a hydraulic lifter=== {{Note1}}Before beginning work, have a clean well lit work area prepared. Use clean lint free rags or paper towels. To clean, use carb spray, acetone, lacquer thinner, or WD-40. To disassemble a lifter, depress the lifter cup using a wooden dowel or a pushrod. This allows the retainer clip to be easily removed from the groove in the lifter body. Use a pick and lift one side out of the groove and the clip will come out.<br> {{!}}Be careful to not accidentally shoot the clip across the shop. Once the clip is out, the pushrod cup and metering disc can be removed, followed by the inner plunger assembly. The plunger can be stubborn, tapping the open end against a cloth-covered wood block will usually bring the plunger to the top of the body allowing it to be coaxed out the rest of the way. [[File:Check details.jpg|thumb|300px|left|Check ball, spring and retainer cup in order]] On the bottom of the plunger you will see a cup and a stiff spring. Remove the spring and set it aside. Inside the cup is a small spring and check ball (left). Some designs use a small disc instead of a ball, however check "ball" will be used herein. The cup is a press-fit onto the plunger, it snaps off and back on. With a lifter that has collapsed or is noisy, often all that has happened is the cup assembly isn't fully seated into the recess on the bottom of the plunger, or a speck of dirt has lodged between the check ball and seat. Remove the cup using a pick and see that the tiny spring isn't bent, kinked or missing, and that the check ball is there and is smooth and shiny, and that the seat on the plunger that the ball seals doesn't have any ridges, burrs, or imperfections that would prevent the ball from seating properly. <br style="clear:both"/> ;Return to [[Lifters#Roller lifter|Roller lifter]]. ===Lifter reassembly=== [[File:Lifter drawing.jpg|thumb|400px|right|Lifter components in order of reassembly]]The plunger gets the cup containing the tiny spring and check ball (no lint!) snapped back into place. Be sure it's seated squarely on the bottom of the plunger. It doesn't take a lot of force, just be sure it's on all the way and sits square on the plunger. Lightly lube the plunger using motor oil, put the stiff spring over the check ball cup on the bottom of the plunger, then insert the plunger assembly into the lifter body (again, no lint). Work the plunger up and down a few times (it'll take a minute to bleed the air from it) to verify it works smoothly and doesn't hang up or have any grittiness. Next replace the metering disc and then the pushrod cup. Using a wooden dowel or a pushrod, depress the pushrod cup and reinstall the retainer clip. Again- be careful to not launch the clip into orbit. At this point the lifter can be depressed and should return smoothly to being fully extended. <br style="clear:both"/> {{Note1}}If trying to repair a bad lifter and the lifter's inner bore is OK but the plunger is found to be unrepairable, replace the plunger assembly from another identical lifter and reuse the lifter body, then replace the lifter back on the same lobe it came from. The lifter is the most precisely machined part in the engine. The plunger OD is matched to the lifter body ID; the close tolerances are required to give the correct amount of bleed down. For that reason, there is a chance you might need to go through more than one lifter to find a good match to the old plunger OD. The MAIN thing is that the plunger not be too tight. Slightly loose will still perform OK, although there's a chance there could be some slight tapping at idle. But if the lifter and cam cannot for whatever reason be replaced as a set, this is STILL preferable to putting a new lifter on a used cam. <br><br> [[Category:Engine]] [[Category:Camshaft]]
|
Editing help
(opens in new window)
Personal tools
Log in / create account
Namespaces
Page
Discussion
Variants
Views
Read
Edit
View history
Actions
Search
Navigation
Main Page
Recent changes
Random page
Help
All articles
Start a new article
Hotrodders forum
Categories
Best articles
Body and exterior
Brakes
Cooling
Electrical
Engine
Fasteners
Frame
Garage and shop
General hotrodding
Identification and decoding
Interior
Rearend
Safety
Steering
Suspension
Tires
Tools
Transmission
Troubleshooting
Wheels
Toolbox
What links here
Related changes
Special pages
Terms of Use
Copyright
Privacy Policy
Your Privacy Choices
Manage Consent